0
What types of routing protocols allow routers to exchange information?
Wiki User
∙ 8y ago
That would be a distance-vector routing protocol. Examples (taught at Cisco Academies) include RIP, IGRP (obsolete in the new version of the curriculum), and EIGRP - but those are only for IP, and there are also distance-routing protocols for other networking protocols, for example, RIP for IPX.
Wiki User
∙ 14y ago
Wiki User
∙ 8y agod. all of the above
It is Distance Vector answer page #275
Wiki User
∙ 8y agoThere are a few common ones. RIP, EIGRP, and OSPF are just some. They just exchange what networks are available.
Wiki User
∙ 11y agothere TCP and IP protocol is used for communication
Wiki User
∙ 11y agoBGP (Border Gateway Protocol) is the most widely used protocol between different ASCaps-lock
Wiki User
∙ 13y agoDistance-vector
Add your answer:
Earn +20 pts
What two characteristics are commonly associated with dynamic routing protocols?
- provide routers with up-to-date routing tables - consume bandwidth to exchange route information
What is RIP routing protocol?
RIP is a routing protocol - a protocol (set of rules) that allows a router to exchange information, with other routers, about existing routes.
To determine the best path routers communicate with each other through?
routing protocols
What does the passive command provide to dynamic routing protocols?
Perhaps you mean the "passive-interface" command in Cisco routers; what this does is that no information related to the routing protocol will be sent through the specified interface. For example, the interface that connects your network to the ISP should not carry any routing protocol information, since the routing protocol is only useful within your company's network.
What is IGP?
Dear All, Clasful routing protocols will not support VLSM because it doesn't send the subnet mask information along with routing information. Classless routing protocols will support VLSM as because it s sending the subnet mask information with routing updates. Regards, Sivaraj C
What describes the process that routers use within a network to learn each other's routes?
routers use routing protocols to exchange routing information. check out the link below for lots of information on routing protocols.
21 what types of routing protocols allows routers to exchange information about best paths with their neighboring routers only?
distance vector routing
What two characteristics are commonly associated with dynamic routing protocols?
- provide routers with up-to-date routing tables - consume bandwidth to exchange route information
What enables routers to automatically manage information received from their own interfaces and from other routers in order to quickly update the routes they know?
routing protocols
What is the differences between routing and routed protocols?
Routing protocols are used by routers (RIP, EIGRP, OSPF) Routed protocols are the actual protocols on the wire (TCP/IP)
What is RIP routing protocol?
RIP is a routing protocol - a protocol (set of rules) that allows a router to exchange information, with other routers, about existing routes.
What is rip protocol?
RIP is a protocol used by routers to exchange information about their routing tables. In dynamic routing, a router learns from other routers about possible routes by advertising what they know. RIP is a protocol that can do that.
What is one fundamental difference between distance vector routing protocols and link state routing protocols?
Distance vector protocols exchange their routing tables, and add a metric to each route. Link-state routing protols exchange topology information, then calculate the routes. As a result, there are the following fundamental differences:The information that is exchanged - routing table vs. topology information.Link-state protocols know the topology of the network (or an area); distance vector routing protocols don't.When the best route is calculated: in distance-vector routing protocols, a metric is added while the route is propagated from router to router. In link-state protocols, the best route is calculated separately by each router, only after having complete topology information.
To determine the best path routers communicate with each other through?
routing protocols
What is flat routing protocol?
Flat routing protocol is a network communication protocol implemented by routers in which all routers are each other's peers. Flat routing protocol distributes routing information to routers that are connected to each other without any organization or segmentation structure between them. Flat routing protocols are primarily those that don't work under a predefined network layout and perimeter. They enable the delivery of packets among routers through any available path without considering network hierarchy, distribution and composition. Flat routing protocol is implemented in flat networks where each router node routinely collects and distributes routing information with its neighboring routers. The entire participating node addressed by flat routing protocol performs an equal role in the overall routing mechanism. Routing Information Protocol, Interior Gateway Routing Protocol and Enhanced Interior Gateway Routing Protocol are popular examples of flat routing protocols.
When multiple routing protocols have a route to the same destination network what determines which routers installed in the routing table?
the distance vector metric
What is ip routing?
Routing protocols implement algorithms that tell routers the best paths through internetworks. Routing protocols include Border Gateway Protocol (BGP), Interior Gateway Routing Protocol (IGRP), Routing Information Protocol, and Open Shortest Path First (OSPF) to name a few. Routing protocols provide the layer 3 network state update. Routed Protocols are transported through a network, such as Internet Protocol (IP), Novell Internetwork Packet eXchange (IPX), and AppleTalk.In short, routing protocols route datagrams through a network. Routing is a layer 3 function, thus, routing and routed protocols are network-layer entities. Routing tables on the layer 3 switch (router) are populated by information from routing protocols. A routed protocol will enter an interface on a router, be placed in a memory buffer, then it will be forwarded out to an interface based on information in the routing table.
