Car Fuses and Wiring
Headlights Tail and Brake Lights
Ford F-150
Ford Ranger XLT

What would cause the brake light fuse to blow on a 91 F-150 when applying the brakes only when the truck is moving?

101112

Top Answer
User Avatar
Wiki User
2009-03-21 20:24:35
2009-03-21 20:24:35

Sounds like a short, But it could be the break light switch.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Possibly warped brake rotor/worn brake pads. Get this checked out.

User Avatar

Warped brake rotor(s). Brake pads and calipers should also be inspected.

User Avatar

Yes, but know that your parking brake on applies your rear brakes. For this reason it is very easy to cause your vehicle to slide sideways when applying only the rear brakes. Also the fact that your parking brake will lock due to the indents, you must use it wisely in an emergency. It also will take quite a long distance to stop any vehicle with the parking brake only.

User Avatar

Steering wheel vibration when applying brakes is usually caused by warped disc brake rotors

User Avatar

The brake pedal has nothing to do with it. If air is in the system then bleed the brakes.

User Avatar

check for loose caliper bolts, brake pad may be moving around in caliper or caliper bracket. missing or broken brake hardware.

User Avatar

a wild panda tampering with your brakes

User Avatar

Vibration when applying brakes is most likely warped rotors. Another cause could be loose caliper bolts.

User Avatar

Sticking caliber. Flush the brake system and install fresh brake fluid, then bleed the brakes. If that does not help, replace both calibers and brake pads on the axle where the brakes are grabbing.

User Avatar

Same as on a car. Applying the brakes means that something stationary is pressed against a moving part. This generates friction, which turns speed into heat.It produces friction, because when the brake touches the rim of the bicycle, the bicycle slows down. (thats called friction) And after a while the bicycle stopsA stationary part is brought into contact with a rotating part. The resulting friction slows the bike down.

User Avatar

warped brake discs can cause your brakes to grab in reverse. Hope this helps.

User Avatar

This is probably due to worn brake rotors on the brakes, if there is no vibration when driving then this will be the cause.

User Avatar

Applying any kind of brake too hard and too fast can cause the rider to fall, period. Disc brakes tend to be more powerful than rim brakes, so an inexperienced rider needs to pay extra attention.

User Avatar

BREAK is To cause to separate into pieces suddenly or violently; smash.WHILEBRAKE is A machine element for applying friction to a moving surface to slow it (and often, the containing vehicle or device) down or bring it to rest.

User Avatar

I'm pretty sure that it would just some dust, rocks, or dirt. I think it could also be that you need new brake pads.

User Avatar

Yes, unless the vehicle has functioning ABS (antilock brake system) brakes.

User Avatar

Vibration when applying brakes is most likely warped rotors. Another cause could be loose caliper bolts.

User Avatar

The brake pads may not be adjusted properly. The wrong brake pads will also cause the brakes to drag. The brake pads may be too thick.

User Avatar

Rear brakes use a 2-stage rotor. Interior of rotor has a brake drum effect with brake shoes Adjust these brake shoes carefully because there is some expansion with friction heat and may cause brakes to drag

User Avatar

Any sudden brake loss can be the cause of 1. brake line damage 2. master cylinder disfunction

User Avatar

There could be a problem with the right brake causing the left to brake harder and pulling to the left. Worn front end parts like a tie rod end can also cause this. Have the vehicle checked out it is not safe to drive.

User Avatar

Yes, and the heat generated is the converted momentum of slowing down.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.