answersLogoWhite

0


Best Answer
Copy

Injectors are bleeding off after shut down, or the engine is running extemely rich, or incomplete fuel burn due to bad plugs, wires, etc. This is serious and will do damage to your engine. Get this repaired ASAP

Also check the fuel pressure regulator. The diaphragm may have ruptured. If there is fuel in the vacuum hose to the regulator you have found the problem

i had an 84 with that problem it was the fuel pump.the pump is located in the driver side of the block and is pushed by the mootor. my pump was warped and did not sit right it caused gas in the oil

User Avatar

Wiki User

โˆ™ 2015-07-17 17:41:24
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: What would make gas leak into the oil on a 1988 Chevy Blazer 4.3 engine?
Write your answer...
Submit

Related Questions

Will a 2.8 engine from a 1988 Chevy beretta fit a 1989 Chevy blazer?

Yes it will, but you have to put all the blazer engine stuff onto the beretta engine...


Will the transmission from a 1988 Chevy s10 blazer with a 2.8 liter engine fit in a 1989 Chevy silverado with a 5.7 liter engine and a 700r4 transmission?

no


IS A 1987 CHEVY TRUCK DOOR INTERCHANGEABLE WITH A 1988 K5 BLAZER?

Are the door interchangeable on an 1987 chevy truck and an chevy blazer 1988


1988 Chevy S10 blazer fuel pump relay location?

Located at front driverside fender inside the engine bay


Would wheels from a 1988 Chevy caprice fit on a 1997 Chevy blazer?

we are trying to find regular factory wheels that fit the lug pattern off of a 1997 Chevy blazer s-10 2 wheel drive


What is the Ignition timing for 1988 Chevy 454 engine?

what is the ignition timing for a 1988 Chevy 454 engine


Can a 4.3l engine out of a 1991 Chevy s10 blazer fit into a 1988 Chevy s10 truck that has a 2.8l engine?

it can but you have to put a 4.3 wiring harness in and a 4.3 chip and you may have to get adapters for you transmission Correct, the 4.3 will not bolt to the 2.8 bellhousing.


How do you adjust the choke on a 1988 Chevy s 10 blazer?

There is no choke to adjust.


How do you set timing on a 1988 Chevy blazer s10 v6?

I have a 1987 Chevy Blazer S 10 4X4 2.8l V6 and the timing recommendation is 10 degrees.


Where is the thermostat located on a 1988 Chevy Blazer S-10?

The thermostat is inside the small housing where the top radiator hose connects to the engine block.


Why are you supposed to note the orientation when changing out the thermostat in a 1988 Chevy s-10 blazer 4.3?

It is important that the spring end of the thermostat is facing into the engine when installed.


Does a 1988 Chevy s10 blazer have a throttle position sensor?

Yes it does. standing in the front of the engine it will be bolted on the left side of the TBI / Throttle body injection unit.


Will the engine from a 1990 Chevy Suburban fit in a 1988 Chevy pickup?

YES, They are the same engines. That would be a direct bolt in.


What size engine in 1988 4x4 s10 blazer?

2.8 or 4.3


Where can you find a wiring diagram of the ignition system on a 1988 Chevy S10 Blazer?

autozone.com


Where is the 1988 Chevy engine control module?

In a 1988 Chevy pickup the ECM is located behind the glovebox.


What size engine is in a 1988 Chevy Suburban?

No


Why would a 1988 Chevy Blazer S10 with a 43 engine 6 cylinder shake?

it might be a broken motor mount. there are two mounts located towards the bottom of the left and right side of the engine make sure you are getting spark to all cylinders. (check for Misfiring)


Why is your engine light on for 1988 Chevy truck?

There is something not right with the engine.


Can you put a V-8 engine in a 4 wheel drive 1988 S-10 Chevy blazer?

Yes, if you check the 4x4 sites there are conversion kits available


What are the speaker sizes in a 1988 Chevy Blazer s10?

The 1988 Chevrolet Blazer front speakers measure three inches by four inches. The rear speakers measure four inches by five inches.


Window on 88 Chevy blazer will not go down?

A blown fuse could be the reason the window will not go down on your 1988 Chevy Blazer. Another possibility is that the switch is worn out or has a loose, broken, or corroded wire.


How do you adjust the choke on a 1988 Chevy s-10 blazer?

There is no choke to adjust on that vehicle, it is fuel injected. If you are having difficulty starting the engine when cold try replacing the coolant sensor.


Where is the ignition switch module located on the 1988 Cherokee limited?

module locatedwhere is the module on a 9 Chevy blazer


What is the gross weight of 1988 Chevy silverado k2500 with the 5.0l engine?

The gross weight of a 1988 Chevy Silverado K2500 with a 5.01 engine is about 2.5 tons. This is equal to about 5,000 pounds.