You will get a short circuit if two uninsulated parts of the supply conductors, touch each other. You can also get a short circuit if the "hot" supply conductor touches any grounded metallic part of the system.
When the cables of the electrical appliances are worn out or it's not connected properly,a short circuit may occure.A short circuit has a very low resistance that almost all electric current flow through it.It'll affect the operation of the electrical appliances.Owing to the heating effect,the excess electric current would produce a large amount of heat,wihout a fuse or a circuit breaker,a fire may be occured when there's a short circuit.
A short circuit will occur when the supply voltage connects directly with the return leg of a circuit bypassing the circuit's load. With no resistive load to hold the current back the amperage goes in to a very high flow very quickly. This is where the over current protection takes over and opens the circuit to cut off the current flow.
If the cables of the electric appliances is worn out or connected not properly,a short circuit may occured.The hort circuit has a very low resistance that almost all electric current flow through it.Owing to the heating effect,much heat will be generated when there's excess electric current.If there's no electric device like circuit breaker and fuse,a fire will be occured.
A short circuit happens when there is no resistance in the circuit.
ANYthing which allows the current to return to the source before it passes through the load.
Usually when the insulation wears thin and exposes the conductor inside, and it touches another conductor.
short circuit occurs when two wire which consist of one live and neutral wire are in contact with the main and the other end of the wire are touched each other short circuit occurs
Short circuit blowing fuse or breaker.
It depends if the short are before or after the device. The short circuit will cause high amperage trough the device and then blown. (JP)
No
Yes, it possible to do a short circuit test of breakers at a project site.
No because a circuit without power applied can only be shown to be a short circuit after the power is applied between the 'right' two points.
difference between p type and n type semiconducter materialAnswerInsulation is used to prevent a short current. To protect the circuit should a short-circuit fault occur is either a fuse or a circuit breaker.
short circuit occurs when two wire which consist of one live and neutral wire are in contact with the main and the other end of the wire are touched each other short circuit occurs
Because a whole circuit needs a short circuit to work. It's like a remote; the remote is the whole circuit and the batteries needed are the short circuit. if those batteries are broken, the remote won't work. In other words, without a short circuit, a whole circuit can not occur successfully. Hope this helped, Charlie the Grey
The circuit resistance is likely to gradually drop and in such case it will cause the circuit to burn down.
No. A circuit breaker is like a fuse, it protects a circuit from a catastrophe if a dead short should occur.
Since load current is determined by dividing the supply voltage by the resistance (for d.c., or impedance for a.c.) of the load, a short circuit would theoretically result in an infinite supply current. This is because a short circuit has, theoretically, zero resistance. In practice, however, the current would be cut off by the operation of an overcurrent protective device -such as a fuse or circuit breaker- which would disconnect the short circuit from the supply voltage. A worst-case scenario could occur should you short-circuit a car battery with, say, a spanner (wrench). With no fuse to protect the battery, the resulting short-circuit current, if sustained, may be high enough to cause catastrophic damage to the battery.
1. That if a short circuit occurs we will get a sign before short circuit will happen or not ? 2. what we can do ? 3. how fuse can get a short circuit ? 4. which wires we have to use from preventing short circuit ?
The fuse in a plug is designed to blow and cut off the current in a circuit before the rest of the wiring and components are damaged or burnt-out should a short-circuit occur.
A fuse is an overcurrent protection device, which protects a circuit by melting in the event of either a sustained overload current, or a short-circuit current. A short-circuit current will occur when a line (not 'phase') conductor makes direct contact with a neutral (or earth) conductor.
It protects the circuit from from further damage if a direct short or overload should occur.
No. A short circuit would be zero ohms.