Auto Parts and Repairs
Brake Pads and Rotors
Ford Expedition XLT
Hand Tools

When replacing the front brakes on a 2000 Silverado half ton 2WD what size wrench do you need to get the calibers of to remove the pads?

282930

Top Answer
User Avatar
Wiki User
Answered
2011-09-14 09:45:08
2011-09-14 09:45:08

It is a 3/8 Allen wrench

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Remove the original brakes and in stall it slowly.

Need to know year of Silverado

How do I remove the heatrest off of a 2000 LT Chevrolet Silverado

how to remove back brakes on a 2002 Chevy surban

If u are talking brake rotors remove the calibers and the calibers support the rotor should almost fall off in your hand

Remove the cover from your 2001 Chevy Silverado stereo. Remove the stereo retaining bolts. Remove the wiring harness and the antenna cable from the back of the stereo.

injectors 6.6 Chevy silverado

how do i repace the headlight sencor in the dash of a 2004 silverado

When replacing your brake pads on your Ford Explorer, you first need to jack up the vehicle and remove the tire. This will give you access to the brakes. Locate the caliper, remove the two bolts and slide the caliper off. Inside the calipers are the brake pads.

How do you remove the rear drum brakes on a 1998 ford escort

Answeron modern cars there is a wear indicator on brakesit will usuall scrape and make a noise when brakes are low enuff to require replacingyou can also see this if you remove wheel and look at brakes50% worn brakes have lots of miles left on them, barring other problems or damage.When they get below 25% is the time to think about new.

To remove the gear shift knob on the '03 Silverado, first pry off the cover that has the shift pattern on it. Then, remove the screw that is under that cover to remove the knob.

after emoving wheel and brake drum you will have to teke brakes off. i usually do one side at a time so i can see how to put the springs back on. once brakes off indo brake line and tthen the two bolts that attach it to backing plate. after replacing you will have to bleed brakes

Block the front wheel to keep the truck from rolling. Lift the Silverado, and place a safety stand under it. Remove the wheel. The drum will pull off, it may take some work as they stick. The brake shoes have a pin through the middle, with a rotating clip and a spring. Remove the clip and spring and the shoes will come off to be replaced.

First remove the tire and brakes, the hub just slides over the lug bolts that hold the rim on, so take it off and replace it. Always put new brake pads when replacing a rotor.

Begin by removing the decorative radio cover in your 2007 Chevy Silverado. Remove the radio retaining screws. Slide the radio out and remove the wiring harness.

How do i remove an air compresser in a GMC Cheyene

The fuel pump is in the tank, and you will have to remove the tank to access it.

How do your remove the lamp housing from a 2002 silverado driving lights? I can remove the upper head light housing but I can't get the driving light housing out.

It is screwed into the passenger LOWER side of the engine block, Just in front of the starter. It has an electric wire pluged into it.when you remove it antifreeze will leak out of the engine block. Just be fast at replacing it.

To install electric brakes, first remove the wheel. Then remove the dust cap, nut, and washer; this will be the place where you install the electric brakes.

Removing a 1991 Chevrolet Silverado door panel is pretty simple. All you will need to do is to remove the screws holding the door panel in place.

how do you remove the spider gears in a 1999 chevy siverado?


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.