answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2006-09-08 14:20:58

Pull the retaining nut then use a puller to remove the harmonic balancer.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

What would cause an engine vibration when in drive at a stop light on a 1996 Ford Contour 2-liter Zetec with automatic transmission?

check harmonic balancer. check harmonic balancer.


Can a rusted harmonic balancer cause the engine not to turn over?

No, a rusted harmonic balancer will not prevent the engine from turning over.


How do you install the harmonic balancer on to install the harmonic balancer on a olds V6 engine?

hay i am jitendra haldar can you Harmonic progression explane with examples


Is there a spacer between the harmonic balancer and the engine?

No.


Can a bad harmonic balancer make a knocking noise?

A bad harmonic balancer can cause a knocking noise. The harmonic balancer doesn't actually produce the noise, but it can cause the noise in the engine.


Does the 1.6L engine in a 1993 Mazda 323 have a harmonic balancer?

Yes, located toward the bottom ot the engine at the end of the crankshaft. Mazda used an integrated harmonic balancer/belt pulley.


Where is 3.4 liter crankshaft position sensor?

The engine is equipped with two. Which one needs replacing? One is located between the engine and transmission on the rear of engine. And the other is located behind the harmonic balancer.


Where is the harmonic balancer on a 1992 tempo?

Harmonic balancers are located on the crankshaft, usually the belt side of the engine.


Where is the timing mark on a Pontiac 326 v8 engine?

on the harmonic balancer.


What are the signs of a blown harmonic balancer seal?

oil leaking from the front of the engine. harmonic balancer doesnt have a seal it does however have a rubber bushing in it this is to take out the virations caused by engine running,hence the name harmonic balancer . you may however have a bad front crankshaft seal that is bad this will leak oil at bottom front of engine so if you are talking bout rubber in harmonic balancer, you will get ruff vibrations from engine when running, also can throw the timing out ANSWER you will have a MAJOR oil leak.....


How do you know when you need to replace the harmonic balancer in your car?

Am unsure of what you are asking. The harmonic balancer is a lifetime part of the engine and does not need replacement based on a time or mileage requirement.


How do you replace a harmonic balancer Mercury Topaz 1992?

The harmonic balancers function is to reduce vibration between the engine and the crankshaft. To replace the harmonic balancer requires a specific tool available at an auto parts store. Loosen the crank pulley via 4 bolts to access the balancer. Using the tool remove the harmonic balancer from the crankshaft.


How hard is it to install the harmonic balancer on a 1992 Olds Cutlass 3300 V6 engine?

Not too familiar with that engine, but never use a hammer to press it on. Go to your local Kragen, Shucks or autozone, they have a harmonic balancer installer in which you can rent. It simply screws into the center of the shaft and evenly presses the harmonic balancer onto the crankshaft.


Where is the crankshaft sensor on a Ford Contour V6?

Pretty sure that it is in front of engine directly above AC Compressor and to the right side of harmonic balancer of Crankshaft. It is mounted horizontally with 2 wires connected.


What size bolt is the harmonic balancer bolt for a 2002 4.7 Dodge Engine?

M14x1.5


Where is the crankshaft position sensor located on a 2002 impala 3.8L engine?

It is located behind the crankshaft harmonic balancer pulley on the bottom front of the engine. The right lower splash shield and harmonic balancer pulley must be removed to replace it.


Crank sensor location on a 1989 Oldsmobile delta 98?

The crank sensor is located behind the Harmonic balancer. Try not to break the rubber within the Harmonic balancer when removing or on the safe side replace both the Crank sensor and the Harmonic balancer ( the big pulley on the bottom - most part of the engine.)


Where is the power steering pump on a 1973 Chevy 350 engine?

At the front of the engine, to the driver's side of the harmonic balancer.


How much torque dose someone need to have on a Harmonic Balancer?

The harmonic balancer torque specifications are different in each type of engine. The general torque specification is between 120 pounds and 180 pounds.


Torque spec on harmonic balancer bolt on v8 350 eng?

The torque specification, for the harmonic balancer on your 350 cubic inch engine, is 280 pounds per square inch. The torque specification may vary according to the manufacturer of the engine.


Where is the oil pump located on the 1997 Isuzu rodeo?

front of engine behind harmonic balancer


Timing marks on a1995 Toyota Celica?

Have you tried looking on the engine block and on the harmonic balancer?


Where is cam sensor location in 7.3?

its just above the harmonic balancer on the passengers side of the engine.


What Smooth crankshaft rotation on a cylinder engine is assisted by using a heavy what?

Harmonic balancer Flywheel


Where is the crankshaft position sensor on a 1997 gmc Yukon?

front of engine, behind the harmonic balancer