The computer in your car has detected a problem with your engine. It could be an oxygen flow problem or something large. Take your car into a Auto care center and have it tested. Many places will do this for free. Get the code and see what the trouble is. Some times there will be more than 1 problem but only the first one will show up and will have to be corrected before the 2nd will appear. If it is just a glitch, detact your battery and let it sit for a couple of minutes. This will clear the computer and the light if there is really no problem and just a glitch.
The engine needs fuel, spark and compression. You are missing one of those.
To reset the service engine light on a 1997 Suzuki Sidekick first turn off the car. Unplug the battery of at least 5 seconds and then plug the battery. The computer will now be reset.
with the ignition off press and hold the miles reset button in on dash now turn on ignition and start engine 'service now' should now be displayed now turn the clock adjuster button either left or right and this should rest the service noification.
does it have a computer, is it correct computer timing may have been moved while swapping.
right now there is no rail service but train service in Afghanistan is to start in the beginning of the year 2012.
Just a FYI for everyone. The following reset my service computer on my 2007 VW Passat 2.0T: 1) Hold down the wrench button (right hand of the trip reset button). 2) While holding the wrench button, turn on the ignition. 3) The computer will now show something like: 'Service Now'. 4) Release the wrench button. 5) Now, press and release the the min (right hand of the h button). 6) Turn off the ignition. 7) Done. The service computer is now officially reset. ENJOY :)
Try resetting the computer
How do you clear the message center computer on an Cadillac seville 1987 Message has bento owner's manual 2 service now?
Error 1053: The service did not respond to the start or control request in a timely fashion. For this error turn off your printer . Reboot your computer And then start your printing all over again. This error is when the printing service crashes. If you still get the message printer spooler service not running. Click start > click run > type in services.msc Find the print spooler service Double click on it And click start service . Then print .
If you have had the dist. out and have it back in now and the engine will start and run with no check engine light on then you are done, the computer will adjust the timing itself. If engine is running and the light is on , then you will have to get a engine scanner and scan the engine in the timing mode and adjust the dist. till scaner saids you are within the specs. then clear codes,tighten dist. your done.
You can't, but you must of had to have a computer in order to have any apple device. It is not yet possible to start a device with out a computer as of now.
ur rear the engine
Mine wont start because the engine is out on the rebuild stand right now, Yours I have no idea
you flooded it
If you have a V8 in you Monte now the corvette engine should bolt right in but you will have to change the wiring and computer.
Check the crankshaft sensor. The sensor connector could be loose or the sensor could be bad. Try to read the engine codes to see if the computer shows an issue.
That's a pretty big question with not very much information. First, I'd plug in a code scanner to figure out what the COMPUTER thinks is wrong. The computer is seldom wrong.
well i know my focus service engine light was on and we just unhooked the battery for 20 seconds and now the light is off and it has been 1 month
I replace engine but now it wont start.
The computer has detected a malfunction. You need to have it checked for codes.
Not at all. It belongs to VAIO messenger. Like any other service, it is possible to stop and start the service as well as configure the service to start on boot-up or by manual start. To do this, go to Start menu, Programs, Administrative Tools, and run Computer Management. In Computer Management, find and open the folder Services and Applications and then select Services. A list will appear on the right, from which you can select Oasis2Services and then click the 'Stop Services' button at the menu icon bar. Double clicking Oasis2Services will bring up the configuration properties, where you can chose Manual instead of automatic for the startup type. Doing so will prevent it from starting on boot. Now you don't have to uninstall the Oasis2Service program perminently.
Put the key in the ignition and turn the power on (do not start the car) Now disconect the negative battery terminal and wait about two minutes. Turn off the key and reconect the battery terminal. The check engine light should now be off. Hard to believe the shop charges $50 for this.
no its totally real use it now i suggest
Replace the fuel filter and use a starter fluid to start the engine.