Best Answer

if this is on a 2stroke the governors are on the throttle handle and the exhaust take the exhaust off at the head and there should be a washer in the exhaust remove the washer. on the throttle there is a screw that stops the throttle from going full throttle remove that screw. there usually by the throttle & to take out just a few screws

User Avatar

Wiki User

โˆ™ 2009-10-07 01:18:48
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where are the governors on a 49cc engine and how do you take them out?
Write your answer...
Related questions

Do you need a lincens for a 49cc engine?


How much motor oil does it take for a 49cc motorcycle?

Most motorcycles or scooters with a 49 cc engine take about 1 liter or one quart of engine oil.

Is a 49cc engine the same as a 4.2 engine?

no a 4.2 engine is in liter's not ccs.

Where is the carburetor located on a 49cc scooter engine?

On my 49cc scooter engine the carburetor is found on the engine. The engine is broken down into 3 parts, the part to the left (looking at it) where the air filter is is right next to the carburetor.

How do you put a 49cc engine back together?

Follow the instructions on Youtube.

What is the biggest engine size to have before needing a motorcycle license?


If you take the pocket bike governor off will it make it faster?

Governors limit the RPM of the engine. Removing it will increase RPM but can cause engine damage.

What is the legal engine size for scotter in free way?

anything over 49cc

What kind of oil does a 49cc take?

SAE 10w30

How fast does a 49cc mini moto engine go?

it goes amazingly 30 or 45

How do you repair a 49cc engine pull cord?

take off the part containing the pull start and retie on another string fed throu the hole and tie on the handle.

What does 49cc mean?

what is a 49cc dirt bike

How do you bore out an exhaust on a 49cc pocket bike?

Answerjust take of the whole exhaust inlcluding the head which is the pipe leading to the engine, take that all of. your bike will be loud as maybe even to load but it will definently give your bike more power. DO NOT DO THIS!!!!! especially on a 2 stroke engine! this will bend your rods and possibly ruin your whole engine!!!!

How fast does a quad 49cc engine go?

50 mph if you undo the 4 flat handed screws on the engine if there isnt it means it is a lawn moer

How do you take the govern off a 49cc pocket bike.?

brake it off haha

What is the legal cc limit on pocket bikes you can ride without a license in What is the legal cc limit on pocket bikes you can ride without a license in Pennsylvania?

49cc. 49cc. 49cc. 49cc.

How do you increace rpm and horse power on a 49cc mini scooter?

buy a new engine for around 149.99 at

How fast does a 49cc engine go on a quad bike?

depending on the mini quad it should go to 30mph-35

How do you take off the governor on a 49cc scooter?

should be where your throtle on your carb. its a screw with a spring.

Is a motor scooter registered as a motorcycle?

Yes in CT if the engine is over 49cc. Check your states MVB laws online.

What should a 49cc 2 stroke engine compression?

Between 120 and 150 psi probably most likely 120ish

How can you tell the difference between a 110cc and 49cc mini chopper if it isn't stamped?

The 110cc. engine will make the bike go about twice as fast as the 49cc. bike. If you can't figure that out than you shouldn't be riding a pocket bike Piston size. a 110cc will be massive vs. a 49cc. block sizes are also a good way to judge. Google it for actual sizes.

Is a license necessary for 49cc cycle in England?

Yes. Anything with an engine needs to have a drivers licence before it can be used on a public road.

How long does it take to get a governors warrant?

In the process of getting one... I was told the governors have a 90-day time limit to review and sign.

Can you put a 70cc pocket rocket engine in a 49cc pocket rocket?

Nope, too much power, will blow the engine. the text above is retarded how can changing the engine blow the engine if a 70cc engine will fit it will work what he's saying is that the rear sprocket is to small. You would have to get a bigger sprocket so the engine won't run at high RPM's when you take off. With the bigger sprocket, the engine will have to work a little more to get the wheel to turn.