answersLogoWhite

0


Best Answer

on the camshaft pulley there are six notches located on the inside lip closest to the block. there is a 2in pin at the 1 o'clock position when viewed from the front. each notch is a certain degree I have yet to verify.

User Avatar

Wiki User

โˆ™ 2010-01-08 04:11:26
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where are the ignition timing marks on the block of a 1989 Nissan Sentra?
Write your answer...
Submit
Related questions

Where is the fuel pump on a 1986 Nissan Sentra Se?

fuel pump on my 1984 nissan sentra DX 4 door is in block next to oil filter under carb


What would be the timing on a 327small block bored out 40 over?

Changing the cyl bore does not affect the ignition timing of the engine.


How do you reset the cam timing and ignition timing when youv removed the distributor from a 1977 Chevy 305 small block?

cam timing will not change ignition timing i would try 8 or 10 degees advance at idle with the vacuum advance disconnected.


Is a Nissan Sentra transmission interchangeable with a Nissan altima transmission?

no. even tho they might use the same QR25DE engine their still different that's why you can find a turbo for a sentra and not a altima its the same block pretty much but headers n trans are different.


Where is the thermostat located on 1998 Nissan Sentra?

Look for the thermostat housing on the back side of the block on the upper left-hand side.


What is the ignition timing for a 1968 Chevy 396 big block?

6 degrees advanced, or BTDC.


What is the ignition timing for a 1986 Chevy 366 big block?

6 degrees advanced, or BTDC.


What is the ignition timing for a 1980 Chevy 454 big block?

4, to 6 degrees advanced or BTDC.


What is the ignition timing for a 1963 Chevy small block 327 cubic inches?

6 degrees advanced, or BTDC.


What is the timing on a 350 Chevy small block with electronic ignition?

4, or 6 degrees advanced, or BTDC, depending on your altitude.


What is the ignition timing for a 1975 big block Chevy 454?

6, to 8 degrees advanced, or BTDC., will work best.


What is ignition timing for a Chevy 396 big block?

Right around 6 degrees advanced, with todays pump gas.


Where do you find the thermostat on a 1991 Nissan Sentra 1.6 DOHC?

For the 1988 1.6 and for most cars, follow the top radiator hose from the radiator to the engine block. Remove the hose from the engine block then remove the flange the hose was connected to (usually 2 bolts but may be 3 bolts on the Nissan). The thermostat is behind the flange.


How do you know a knock sensor is going bad?

Tap the block or head with a hammer while the vehicle is running. If the engine slows down as you are doing this, it is sensing "knock" and trying to compensate by retarding ignition timing. Tap the block or head with a hammer while the vehicle is running. If the engine slows down as you are doing this, it is sensing "knock" and trying to compensate by retarding ignition timing.


Where is the crankshaft positioning sensor on a 2003 Nissan Sentra?

Its just above the right inner CV joint, plugged into the bottom/ back side of the engine block. You can only get to it from under the car.


What is detonation sensor?

An engine may have one or more knock or detonations sensors in the block. The sensors use piezoelectric materials to detect vibrations in the block. If a certain vibration known to be caused by pre-ignition is detected, the ECU can take action, such as reducing ignition timing advance.


Where are the ignition timing marks on a 1991 Mercedes-Benz 190E 4-cylinder?

Timing marks are always on the crankshaft, usually on the pulley closest to the block. This is because the timing must be based upon the position of the number one piston, which is connected to the crankshaft.


What is the ignition timing for 427 Chevy big block 1973?

6, to 8 degrees advanced, or BTDC, will be about all you will be able to run, on pump gas.


Ignition timing for a 1970 402 big block Chevy?

There are contributing factors, however, about 6 degrees advanced or BTDC., should work best.


What is the ignition timing for a 1972 Chevy 400 small block?

4, to 6 degrees advanced, (BTDC) initial, or 30, to 32 degrees total.


Small Block Chevy 350 timing?

how do i set the timing for a chevy 350 small block?


Where is the theromastate 1991 Nissan 300 zx?

The *thermostat* is behind the timing cover where the radiator hose goes to the engine block in the front-center of the engine


How do you adjust the timing on a 1989 Chevy 2.2 with coil packs?

If it is a distributorless ignition system, you don't. The timing is all handled by the ecm. It picks up the signal from a crank sensor in the block. It has a reluctor wheel cast in the crank.


Where is the solenoid on a 1995 Nissan Sentra E?

If it is anything like my 1991 Nissan Sentra (and it probably is), the solenoid is actually attached to the top of the starter. The starter is located underneath the car, attached just below the engine block but on top the transaxle (where the transmission connects with the axle) it is very difficult to get to, on mine I had to remove the air-intake manifold and a few mounting brackets below the car.


How do you change the spark plugs on a 2004 Nissan sentra?

i changed plugs on my 2000 sentra it should be the same procedure just loosen the screws to the four caps on the top of ur block and take them out and replace 1 by 1 if u have the paper i would go with pre-gapped plugs preferably platinum NGK

Study guides

๐Ÿ““
Create a Study Guide