answersLogoWhite

0


Best Answer

The knock sensor is located in the engine "V" under the upper and lower intake manifolds, and under the coolant crossover pipe. It requires considerable disassembly to get to. If you have a code for the knock sensor, be advised that the knock sensor is probably NOT the problem. Many problems will set the code for the knock sensor because they share part of the circuit. There are two oxygen sensors, one at the front where the exhaust pipe comes down and turns toward the back, and one behind the second converter, under the passenger seat.

User Avatar

Wiki User

โˆ™ 2012-09-10 04:12:08
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where are the knock sensor and O2 sensor located on a 1999 Mercury Villager?
Write your answer...
Submit
Related questions

Show where the knock sensor located?

can you tell me where the knock sensor is located on a 3.3l mercury villager


Where is the knock sensor located in the 1999 Mercury Villager?

the knock sensor is under intake, must remove intake and it is under two coolant lines.


How do you install a knock sensor in a 1993 mercury villager?

the elictronic control sinsor at on a 93 mercury villager


Wheres is the knock sensor located on a mercury villager?

The knock sensor is located - are you ready for this? - in the valley of the engine under the intake manifolds. Both upper and lower manifolds must be removed to gain access.


What does the knock sensor look like on a mercury villager?

This is an image. (below)


Location of knock sensor on a 99 Mercury Villager?

It is under the intake manifold.


How do you change a knock sensor on a 1999 mercury villager?

The knock sensor is under the intake manifold, which has to be removed. This should be left to an experienced mechanic.


What years inner change with a 2000 mercury villager knock sensor?

1999 - 2002.


What are some Prices for a knock sensor on a 1999 mercury villager?

I payed $117.00 at auto zone


How do you replace a knock sensor on a mercury villager estate 3.6 engine?

There's no need to replace knock sensors, and there was never a 3.6 engine.


What is the function of a knock sensor on a 2000 mercury villager?

the knock sensor monitors preignition,spark knock and sends signal to pcm,pcm responds by adjusting ignition timing and fuel timing until knock is gone.


Where is the location of knock sensor on 2001 Mercury Villager?

It is under the intake manifold. Darn hard to get to and expensive to change.


Donde esta colocado el knock sensor de la mercury villager 2000?

donde esta colocado el knock sensor en una Chevy silverado 2000


Why do you still get a bad code for the knock sensor after you put a new knock sensor on your 1999 mercury villager but still get a bad code from the computer?

Because there is nothing wrong with it. This is a common code that can relate to a number of components. The knock sensor itself is rarely the problem.


Where is 2001 mercury villager knock sensor located?

It's in the center of the block. Engine disassembly needed. <><><><><> Not certain, but I thought knock sensors were mounted to the head or intake manifold in such a way that they could be replaced without major disassembly.


Will a bad knock sensor make a 1999 Mercury Villager stop running?

No. The knock sensor alerts you to the fact that there is an engine vibration that needs attention. Mine has been awaiting replacement for six months.


Is crank sensor and knock sensor on 2000 villager same thing?

no, it is not.


How do you remove the knock sensor from a 1997 Mercury Villager?

It's under the intake manifold. The whole assembly needs to be removed, it's a complex process.


Where is the knock sensor in a 2000 villager?

the knock sensor is under intake, must remove intake and it is under two coolant lines.


Where is the knock sensor located 1999 mercury mystique?

Low on back side of engine block.


Where is the iat sensor located on a 95 Mercury Villager?

Located underneath the intake manifold. It is threaded into the underside. It senses the temperature of incoming air for combustion. It has really small wires that come directly off of it. Not to be confused with knock sensor wires, which are a little thicker and located under lower intake manifold. Frank


Where are the locations of the crankshaft sensor and knock sensor on a 1998 Mercury Villager?

i have been working on one lately myself i have been trying to figure out. i cannot help on were the crank is yet, but, i do know the knock sensor is under the intake about dead center, you do have to take off the upper and lower both off totaly. I do also know that the knock sensor is not cheap either.


What are knock sensor symptoms?

There are no symptoms. The knock sensor is a passive part that does not do anything if it's not activated. Knock sensors codes on the Villager/Quest are usually caused by some other component, not the sensor itself.


Where is the knock sensor located on a 2000 Mercury Villager and is it easy to change?

you will have to remove intake and you will see it underneath two coolant lines. can be done. time cosuming and a lot to take apart. ON THE ENGINE HEAD AND IT IS VERY HARD TO BE CHANGED.


Where is knock sensor located on 2006 Chevy Impala SS?

Where is the knock sensor located on impala SS