Best Answer

Spark plugs are always either located on top of valve cover or front or back of cylinder head. Always use the correct tooling which is a spark plug socket which has a rubber seeling in the inside to hold the spark plug while removing and protecting the plug from breaking. Its good to get the recommended spark plug and checking the spark plug gap before replacing new one.

AnswerTrace the spark plug wires from the distribution system and you will find that they are on the back side of the engine (nearest the firewall). No, there is no EASY way for the layman to change any plugs located like that. Feel is the best way to get them out -feel where plug is, guide the plug socket over plug, undo it and remove. In some cases, you can use a dental type mirror to reinstall the plugs. I suggest doing them one at a time to keep your firing order in line. AnswerActually I have a 2000 Mitsubishi Galants and they are not on the backside of the engine. Mine are on topside of the engine behind the oil cap. There are two types of spark plugs on the 2000 Galant. Two that are connect to a psuedo-distributor and the other two have small black boxes on the which are computer sensors that are constantly reading the spark timing. It is actually very easy to change them. The plug wire socket pops off and then you can screw the plug out. just make sure that when you remove the two with the computer boxes on them that you do it very carefully not to bend or bang the box, cuz them you'll have a problem. AnswerJust changed the spark plugs on my 2000 Galant 4cyl....very easy! The above answer is very informative, the plugs are located directly on top of the motor behind oil cap.The only thing I will add:make sure you have some way to remove the plug from the engine(the plugs are about 7" down inside the motor)once you loosen the plugs you still have to some how get them out.I didnt have a tool that would fit down the hole to grab it so I stuck a few pieces of bubble gum into the spark plug socket and they came right out(kinda like putting gum on the end of a stick to get a coin out a gutter)It takes a total of 15min.Good Luck. :-)
User Avatar

Wiki User

โˆ™ 2011-09-14 10:54:09
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: Where are the spark plugs on a 2000 Mitsubishi Galant and can you change them without much trouble?
Write your answer...
Still have questions?
magnify glass
Related questions

How do you change the oil in a 2005 Mitsubishi galant?

Same as any other car. Eliminate the Mitsubishi Galant and this has probably already been answered.

How do you change a rear wheel bearing on a Mitsubishi Galant?


How do you change belts on 2003 Mitsubishi Galant?

were are the timing marks at

How do you change the transmission mount on your 2004 Mitsubishi Galant?


How to change a transmission in an 01 Mitsubishi galant?

In order change a transmission in a 2001 Mitsubishi Galant, it is best to change the solenoid first. it is then recommended that you take the car to a certified transmission garage to do the work.

Changing the spark plugs on a 2006 galant?

how to change number 6 spark plug on a 2006 mitsubishi galant

How do you change spark plugs for a 2003 Mitsubishi galant spark plugs?

2002 galant , can't find the spark plugs

2005 Mitsubishi galant fuel filter location?

how to change fuel pump on mitsibishi galant 2005 2.4 liter

Can you change the starter on a 1993 Mitsubishi Galant easily without removing an axle? may need some special body contorsion.

When should you change a timing belt on a 2003 Mitsubishi galant?

when it doesnt work

Where are the spark plugs on a 2000 Mitsubishi Galant v6 and can you change them without much trouble?

My 2002 Galant has not had spark plugs replaced for over 100k due to where they are. Three are underneath the intake manifold. Yes...intake has to be removed. Not difficult now that I know. Lots of bolts and hoses need to be removed to lift the manifold.

How do you change thermostat on 99 Mitsubishi Galant?

The thermostat on a 99 Mitsubishi Galant is changed by draining the coolant, removing the upper radiator hose, and unbolting the housing. The thermostat can then be removed and a new one put into place.

People also asked