answersLogoWhite

0

  • European Cars
  • Headlights Tail and Brake Lights
  • Chevy Cheyenne
  • Jeep CJ

Where are the wires routed for the high brake light in a 97 Mercedes E320?

User Avatar

Wiki User

βˆ™ 2006-08-29 16:21:50


Your Answer

Loading...

Related Questions

Mercedes c series backboard brake light is not wrkg but bulb is good?

Have you tested the fuse?? Sometimes the wires or the plug where the bulb is plug in. Or the brake bulb, it sends the electric signal when you push the brake pedal.


Where is the brake light switch on 1994 Dakota does it have 6 wires?

Just above the brake pedal, yes it has six wires.


Why isn't the brake lights coming on when the pedal ispressed on a 93 Honda accord?

check for blown brake light bulbs and broken wires. also check brake light switch on brake pedal


Why wont brake lights work on 1996 ford escort fuse and bulbs have been replaced?

check the wires at brake light switch on brake pedal they are bad about breaking brake light switch


Brake light and air bag light come on when you accelerate and go off when you brake what could it be?

IT SOUNDS LIKE A SHORT SOMEWHERE OR MAYBE CROSSED WIRES.


My third brake light comes on with my parking lights?

Short in wires or wired incorrectly.


You have no brake lights on a 95 golf all bulbs are good where do you start to look for the problem?

try your brake light swtich on the brake pedal and check wires


Why do interior lights go on when brake is applied?

There probably is only one cause for your interior lights to go on when you apply the brakes. There probably are brake light wires and interior wires that have warned together.


Where is the brake light switch on a 94 Aerostar?

It is on the brake pedal. There should be two wires connected to it. I found it last weekend after I could not get the van out of park, one of the wires broke off the switch.


Why is third brake light the only one working on a 2007 landrover lr3?

There are a few reasons that the third brake light is the only one working. One reason could be that there is a short in the wires of your main brake light. Another reason is that the light bulb has blown out.


Location of the brake light switch 1973 Volkswagen bus?

There are some wires coming from your master cylinder, under the floorpan on the driver's side... those are you brake light switches


How do you change a brake light switch on a 1998 Chrysler?

Probably located at top of brake pedal secured by 2 locknuts and 2 wires


Where is the brake light switch on a 1963 Galaxie 500?

The brake light switch is threaded into the master cylinder. Open the hood, look at the brake master cylinder, notice the brake light switch with wires connected. Have new one ready to install when you remove the old one to keep loss of brake fluid to a minimum.


Where are all the brake light grounds on 1990 sundance when the headlights are off then brake lights are fine but when u turn headlights on then the brake lights don't work except the cyclops lights.?

You probably have a loose wire connection in the brake light sockets. Insert a nail or probe tip into the back of the light socket where the wires are inserted and test the brake lights. (The socket can appear perfectly normal and the wires may even seem well attached.)


Why brake light turned off after headlamps turns on headlamp off brake light on 1 reverse light work?

you have some wiring problems. sounds like wires a crossed or you have a dead short somewhere


Where is the brake light located on a 2001 sable wagon?

Other than at the back of the car... (?) If the question is about how to change brake light bulbs, See "Related Questions" below If the question is about the brake light switch, that's on the brake pedal - just a couple of wires going to it and rather easily replaced.


Why does Brake light goes out when headlights are on?

probably bad headlight switch,the break light wires run through the headlight switch


How do you change a Eye level brake light peugeot 206 2002?

open the boot, on theapposite side of the brake light there are 2 nuts and bolts. undo them and the light will come off. cut the wire connecting the brake light then use clip or crimp wire connectors to the 2 wires


1992 Chevy caprice brake light stays on but the brakes are off?

brake light plunger switch on the brake pedal maybe faulty, remove it and connect the two wires together and pull apart and see if lights go on and off


Brake light switch Ford Escort 1997?

It is just above the brake pedal, mounted on a bracket. You should see the sensor and the wires right above.


If your brake lights work but not the tail lights and its not the fuse?

Have you checked your bulbs ? The tail light / brake light bulb has 2 wires inside it In my case I have had to change each bulb because the brake light portion did not work but the tail light portion of the bulb did ( I'm assuming that your front park lights are working )


Wire a third brake light on a hot rod?

you have to pull the feed wire off the brake switch to supply power to the new third brake light. get a test light and test the wires on the brake switch....one is hot all the time the other one gets hot when you depress the pedal....that is the one you need. do not take it pull your power from the rear light it might have an intergrated turn signal wire. which would make your 3rd brake light blink.. ok.have fun! you have to pull the feed wire off the brake switch to supply power to the new third brake light. get a test light and test the wires on the brake switch....one is hot all the time the other one gets hot when you depress the pedal....that is the one you need. do not take it pull your power from the rear light it might have an intergrated turn signal wire. which would make your 3rd brake light blink.. ok.have fun!


Why does one brake light work and the other brake light does not work?

One possibility is, on multi-light tail light assemblies, is a burned out bulb. Some cars have separate light bulbs for tail, brake, turn, and backup lights The other possibility is an electrical short in the wiring. Somewhere in the miles of wires, two wires have crossed or the insulation has worn off and is shorting to the chassis. The only cure is to trace out each individual wire with a voltage meter.


97 crown Victoria tail light don't work?

i am not sure you mean brake lights or tail lights.If brake lights don't work.You have to check out a brake light switch,(it conects to your brake pedal) make sure both wires are conected to the switch.And if tail lights don't work, you have to replace a head light switch.(where you turn your head light on and off)


How do you replace brake light switch on suzuki forenza?

To replace the brake light switch on a Suzuki Forenza, locate it on the pedal shaft, release the wires that connect it, twist and then take out the old brake light switch and put a new switch in its place. The job can be done by any handy owner.