Most likely you did not align properly the mark, it causes the engine to have wrong timing as result the engine knocks.
it is a gunlike device wich fires light and it is used to align properly a timing chain in an engine.
The 97 S10 2.2L engine doesn't have a timing belt.
The timing marks on a Nissan 2.4 engine are located on the camshaft sprocket and the crankshaft sprocket. The timing belt connects both together which must align perfectly.
You are changing the timing belt and you need o know where the timing marks are for the cam shaft and the crankshaft on a 1994 corolla Also how do you align the marks to put engine in time?
If you are asking how to replace and align a timing belt. This job is best left to a professional, which you are not, or you would not ask this question. Serious engine damage will occur if done incorrectly.
timing on 4m 51 engine
align the crankshaft pulley mark with mark on oil pump housing, and align marks on cam gears with marks on rear cover, then install timing belt.
A timing light on #1 cylinder and align the timing marks on crankshaft and stationary mark on engine block
how do you align timing mark on 97 1.8 Mitsubishi mirage
Timing marks align differently on every vehicle dependant on the engine used and the manufacturer. To find the proper alignment marks for your vehicle pick up an auto repair manual from a parts store ( they can also be found online ) and follow the directions to the letter. Be especially careful if your engine has interferrence heads.
engine speed, engine load, coolant temp, throttle posision and intake manifold pressure
Timing marks are located on the camshaft of a 1982 Toyota Tercel. The timing marks help correctly align the cams so the cars engine can run properly.
usually have to align a mark on the cam pulley up with a mark on the chain back cover, and align the mark on the crank pulley up with another mark on back of chain cover. and make sure all marks are aligned up and turn engine by hand before starting engine
There are 4 camshaft sprockets that must be aligned perfectly for the engine to function properly, and if the timing is off very far the engine can be completely destroyed. A special alignment tool is available that holds the camshaft and crankshaft sprockets in alignment while you replace the timing belt and adjust the tensioner pulleys. That's about the only way to properly align the timing sprockets, and the only way approved by the manufacturer.
When you set to do this on your own, it is critical that you get it right from the beginning, or you risk destroying your engine. The most important thing is to ensure that all the marks on the gears align correctly with the corresponding marks on the timing belt. Wind the engine over by hand to ensure the marks on both sides align properly, before you replace the covers.
Look for detent marking on camshaft sprockets and align them with timing marks on cylinder head, should be visable markings and ensure that engine is at TDC on compression stroke, and timing marks should all line up
There are 3 timing marks to consider on timing the Mazda r2 just like any engine. crank timing, fuel injection timing and the valve timing. these 3 have markers to align. The crankshaft have timing marks on the pulley pointed by a pointing rod. 4 lines marks the timing. the crankshaft is dead center on the first cylinder whene the pointer is pointed on the center of the foul lines. The injection pump is marked by a line on the pulley and the notch on the plate of the front cover. The camshaft is marked the same way. Be sure that you rotate the pulley clockwise to align these marks to ensure tightness of the timing belt.
align the cams to the E & I marks on cam. You will see notches right beside them. Align the crank with key way up.
There's no way to set timing. Just align marks on camshaft and crankshaft during belt installation. There may be another problem if your car is still running rough.
It is a mess, but you need to take it apart and align the marks right. The way it is now, it should not and will not run. You could of messed up the inside parts! The timing is crucial.
There is one on the timing belt plastic cover and it's a scale from 0 to 15, another park is on the engine body behind the camshaft pulley. The hole in the camshaft pulley must align with the mark on the engine body and zero on the timing belt plastic cover.
Timing mark on the crankshaft pulley (mark should be at zero) must be aligned with the mark on the camshaft pulley (mark should be in the middle of the hole in the pulley).
Adjusting the distributor sets the ignition timing. To set timing you need to align the timing marks as specified by the manufacture using a timing light.
In order to do this properly, you need the correct tools as well as an owner's manual and a repair manual for diagrams that show the relevant parts and their names, ignition marks and so on. The manual is also necessary in order to understand some of the terms named here. You should prepare well for this job in order to avoid mistakes which could be serious. Procedure: The engine should be cold. Use the crankshaft pulley bolt to turn the crankshaft and align the timing marks on the crankshaft timing pulley and on the oil pump body. Remove any oil or water on the crankshaft timing pulley,idler pulley and water pump pulley, and keep them clean. Align the installation mark on the timing belt with the drilled mark of the crankshaft timing pulley. Install the timing belt on the crankshaft timing pulley, also on idler and water pump pulleys. Crankshaft Position: Turn the crankshaft pulley, and align its groove with the