Car Fuses and Wiring
Jeep Cherokee Sport
Jeep Grand Cherokee
Jeep Grand Cherokee Limited

Where can you find wiring diagram for auto locks on a 1993 Grand Cherokee?

121314

Top Answer
User Avatar
Wiki User
2008-06-01 18:24:46
2008-06-01 18:24:46

Pick up a "Haynes automotive repair manual" at any local auto parts store (AutoZone, Advanced Auto Parts, Etc.). They have wiring diagrams in the back of the book. Should cost about $15.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The 1990 Jeep Grand Cherokee power locks wiring diagram can be obtained from most Jeep dealerships. The wiring diagram can also be found at most auto-parts stores.

User Avatar

The 1997 Jeep Grand Cherokee power door lock fuse can be found in the fuse box. The fuse will be in the first column, third from the bottom.

User Avatar

how do i fix my 1998 jeep grand Cherokee when the wheel turns right it locks up and I cant turn it back. If I put it in reverse it will unlock and I can drive again.

User Avatar

you have a cut wire in the drivers side door wiring, they get opened & closed so much that wires get cut, open the black boot in the door jam & you'll find your cut wire.

User Avatar

If you have a 1993 Jeep Cherokee Country check the wiring harness underneath the driver

User Avatar

In the back of a Haynes repair manual or autozone.com there you will find online repair manual's

User Avatar

If you wait long enough the problem will not be intermittant anymore and you can fix it. Sounds like an electrical problem to me if they all are doing it and the problem should be in the driver's door. I would be looking at the wiring harness that goes through the rubber boot tween the door and the body....that's where the most flex in the wiring comes from.

User Avatar

There could be many reasons why the 1993 Grand Marquis make noises when the doors lock. The wiring could be off, or the motor could be going out.

User Avatar

In a Honda Integra, you can convert manual locks to power locks. You can either purchase a kit and do all the wiring yourself, or you can purchase doors from a junk yard and redo the kit. By purchasing doors, the wiring is already set up.

User Avatar

A very common problem is to have broken wires in the harness going to the driver side door.

User Avatar

i had this happened, went to a junk yard and 35 dollars for the actuator. took about 15 minutes to install.

User Avatar

you go to the parts store and buy new locks for your doors.

User Avatar

Check the fuse box located behind the battery. I washed my gf's 93 grand Cherokee once and soon after, it started smoking and the locks and instrument panel wouldn't work, turns out that it was that fuse box and the wires were all burning.

User Avatar

Call a locksmith or local police department i called my neighbor, Cherokee wrecker in acworth ga and he used a tool to bow out the top of the window and reached in and bumped door locks to open

User Avatar

To repair the wiring on the trucks door locks, you will have to find the problem first. Check all of the wires connectors for loose or bad connections, and look for any places in the wiring where the insulation has worn through.

User Avatar

Which ever one or ones are making the noise, the lock actators have gone bad. The actuator comes as part of the door latch.

User Avatar

Fuse diagrams are in the Owners Manual - which are freely available for convenient download (See "Related Questions" below)Since both of the door locks and window switches are in the same panel, and share a wiring harness, I would suggest looking at the switch connectors and door wiring.See "Related Questions" below for more

User Avatar

The only way i found to disarm the alarm was to use the back hatch lock. lock it and unlock it a few times with the key. if this doesnt work try the door locks


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.