Best Answer

Haynes repair manuals has good diagrams

User Avatar

Wiki User

โˆ™ 2004-10-21 13:58:37
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: Where can you get a diagram of the pulleys and timing belt position for a 2001 Mitsubishi Galant 2.4 liter 4-cylinder?
Write your answer...

Related Questions

Belt diagram for a Crown Victoria?

What year is your Crown Vic? On the later models (199x through 200x) there is a sticker on the radiator support or the removable filler panel between the grille and the radiator support that shows all the pulleys and the belt position on the pulleys. It is located near the emissions control sticker.

How do you replace the serpentine belt on a 1999 3.0L ford ranger?

Make a diagram of all the pulleys and draw the belt in. Locate the belt tensionor. Loosen it. Slide belt off of the pulleys. Look at your diagram and install the new belt. Tighten tensionor. There should be little play in the belt after being installed on the pulleys.

Is there a Diagram of pulleys on 1993 Mercury Villager?

Yes carquest napa or checker auto parts

Where is cylinder 4 on a Mitsubishi Galant?

what engine size? 2.0 mounted with belts and pulleys to drivers side. 4,3,2,1 to driverside.

Where is the oil pump on a 99 galant?

The oil pump on a 1999 Mitsubishi Galant ES, is located behind the crankshaft an timing pulleys. You'll have to dismount the oil pan, all the timing belt system and all the pulleys nearby to get to it.

How are moving pulleys different from fixed-position pulleys?

A moving pulley is a wheel on an axle designed to support movement without a center point being fixed. A fixed position pulley does not change positions and rotates only in one direction.

How do you get the serpentine belt at proper tension on 1990 Suburban after replacing alternator?

Some where in the radiator shroud or engine compartment there should be a serpentine belt diagram. Follow diagram or picture. Rotate the drive belt tensioner away from the drive belt and install the drive belt on the alternator pulley. also the pulleys the smooth side of the belt goes on the smooth pulleys the belt side with the teeth go on the pulleys with the teeth

Where can you find a diagram for the pulleys on a 350 engine?

The diogram is usially behind the ratiator if it is not then it would be under the alternator. If you want the Serpentine Belt Routing diagram for your 350 go on www.alldatapro .com.

How does the belt go back on?

look at the cover on your radaitor somewhere in that vicinity there should be a diagram showing how it goes over the pulleys

Diagram 88 fiero alternator belt?

It goes around three pulleys and is very easy. it will work fine if you guess

What does a fan belt diagram for a 98 Cadillac Eldorado?

When you ask, "what does a fan belt diagram..." I can only guess that you; 1. Need the belt diagram 2. Want to know what the belt diagram is for. In answer to #1: Check around the engine compartment or in your owners manual if you need a diagram. In answer to #2: The diagram is for the proper location of the serpentine belt on the engine pulleys

Do you have a diagram of the timing marks alignment between the crank and the cam shaft pulley?

There is a line on both of the pulleys, the top pulley (camshaft) the line should be at the bottom or 6:00 position and the bottom pulley (crankshaft) the line should be on top or in the 12:00 position, both lines should line up with each other.

What is the timing belt routing for a 2000 Toyota Solara with a 4Cylinder Engine?

when you buy a replacement belt buy a kit that also contains idler pulleys. its best to change them all at once. it should have drawings to show you proper routing and installation instructions.

Why does your 96 Mitsubishi Galant make a squealing noise?

Possibly loose belts slipping on the rotating pulleys. Need tightening which isn't a complicated job but need to be careful not to over tighten which could cause damage to the pulleys and the belts could break if old.

How do you put the timing belt back on a 1991 Mitsubishi eclipse without removing the pulleys?

There is a tensioner pulley that must be removed or pulled out of the way. Get all of the pulleys aligned in the spot s where they need to be. Make sure that when you put the tension back on it that they stay in the correct spots.

How do you route a serpetine belt on a Chevy Tahoe?

around the pulleys! There should be a routing diagram under the hood on a sticker on the air filter housing

Is there a belt diagram for a BMW 328i 1997?

try this link:

Where is the crankshaft position sensor located on a 2004 Mazda RX-8?

The crank position sensor is located on the front of the engine, behind the lower crank pulleys.

Examples of pulleys in everyday life?

Gym pulleys Window blinds elevator pulleys garage door pulleys

Do flagpoles have pulleys?

yes the do have pulleys

What objects are pulleys?

Pulleys are simple machines.

Where can you find a diagram of serpentine belt for 1999 Dodge Dakota?

Is the diagram on radiator support gone? Try an auto parts store they may have one a dealer will have one. Or do like I do. The back side (smooth side) of the belt will always go on a smooth pulley & ribbed will go on groved pulleys. Mark on a PC of paper the position on each pulley & which are groove-smooth. Takes a few min to figure out but it will work,

How do you put new mower deck belt on?

All manufacturers do it differently but you need to locate the belt routing diagram which for the most part is somewhere on the deck or under the seat, otherwise you need to look in the owners manual. Route the belt through all the stationary pulleys saving the idler ( moveable or has spring tension ) pulley for last. Move the pulley to a position where the belt can be placed in position and release.

What are the kinds of a pulley?

FIXED PULLEYMOVABLE PULLEYBLOCK AND TACKLEAdditonal answerFlat pulleys, v-pulleys, multi-V pulleys, jockey pulleys

Who uses pulleys in their jobs?

Many people use pulleys in their jobs. The rides like Supreme scream, which go vertically up and down have pulleys in them. Elevators have pulleys in them, and people who ship cargo use pulleys in their cranes.