answersLogoWhite

0


Best Answer
Copy

Get a motor manual.

2006-09-08 21:55:02
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

How do you replace a serpentine belt on a 3.8 liter Chrysler engine?

Disconnect the battery. Taking a ratchet and socket rotate the belt tensioner to release the belt. Remove the belt and install the new one. Release the tensioner, and connect the battery.


How do you tighten serpentine belt on 2005 Chrysler 300 2.7 liter v6?

You can tighten the serpentine belt on your 2005 Chrysler 300 by tightening the tensioner pulley. Push the tensioner pulley to the right until the serpentine belt is tight.


How do you adjust the belt tensioner on a 1988 Pontiac Tempest 2.8 liter?

You don't. they are not adjustable. Its a spring tension on it, therefore you would have to replace the tensioner which only takes one bolt to get the tensioner off. Same thing to re-install the new one!


Does anyone have manual instruction on how to install an exhaust manifold on a 98 iszuzu rodeo 4cylinder 2.3 liter 5 speed?

Nope.


How do you change belt on Chevy 2.2 liter 1994 engine?

Well, on my 91 you have to move the belt tensioner off the belt by placing a 14mm wrench on the nut and move the tensioner off the belt. Remove the belt, release tensioner. Re-install in reverse order. Hope that helps.


How do you move the idle tensioner for a 1998 3 liter dodge?

"How do you move the idle tensioner for a 1998 3 litre dodge?"


What tool is required to install a serpentine belt on a 2.4 liter Chrysler Sebring 4 cylinder?

go to http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008948b


How many quarts does the 3.8 liter Chrysler motor for Chrysler hold?

5


What is a 2.7 liter Chrysler sebring?

It is an automobile.


How do you remove replace the tensioner on a 96 3.3 liter Caravan?

You have to remove the belt first, this is easiest with a tensioner tool. Then the nut that holds it to the bracket is on the backside of the tensioner and needs to be done from the bottom.


How do you change the serpentine belt tensioner on 2.4 liter 1998 Malibu?

remove the belt. then in center of the tensioner is a bolt that goes into engine. remove this bolt. then tensioner should come off.


How many quarts of oil does a Chrysler pacifica hold?

A 3.8 liter Chrysler Pacifica hold approximately 5 quarts of oil. A 4.0 liter Chrysler Pacifica hold 5.5 quarts of oil.


Will the transmission 3.0 liter fit a 3.3 liter engine?

Dodge, Chrysler, Plymouth no.


Will a 3.3 liter Chrysler intrepid engine fit a 2000 Chrysler concord?

If the original motor of the concord is a 3.3 liter then yes because they are the same motor.


How do you replace the serpentine belt on a 3.8 Liter - V6 2000 Grand Prix GT?

look how it is routed before removal. There is a tensioner that holds the belt tight. Use a wrench to hold the tension off the belt while you pull the out from under the tensioner. install new belt the same as old.


How do you replace serpentine belt on a 2000 Chevy cavalier 2.2 liter?

Note:The drivebelt routing decal on the radiator shroud to help during drivebelt install * To replace the belt rotate the tensioner pulley clockwise to release belt tension * Remove the belt from the auxiliary components and slowly release the tensioner * Route the new belt over the various pulleys again rotating the tensioner to allow the belt to be installed then release the belt tensioner


Is the Chrysler 3.5 liter an interference engine?

Yes


Is the Chrysler 2.7 liter and interference engine?

Yes


Who makes the 4.7 liter for Chrysler?

I'm pretty sure that Chrysler themselves designed and build that motor.


2.7 liter Chrysler engine an interference engine?

YES


Firing order 2.5 liter v6 Chrysler?

123456


Does a 3.2 liter Chrysler motor have a timing belt?

Yes


Where is a logic control module on a 1995 Chrysler concord 3.3 liter?

The logic control module on a 1995 Chrysler Concord 3.3 liter is on the passengers side. it is located underneath the dash.


How do you install a drive belt on a 2000 jeep wrangler 2.5 liter?

how to install a drive belt on a 2000 jeep wrangler 2.5 liter


How do you replace the belt tensioner on a 3.0 liter Mitsubishi engine?

There's a 15mm nut on the back of the tensioner you have to remove. It's hard to find and a tight spot but a regular wrench will get it out.