0
Where can you get torque specs on your ZZ4 aluminum head rocker studs?
Wiki User
∙ 17y ago
http://torquespecs.xoompages.com/gmfs70-88chv8.htm the rocker studs are 7/16-14, same as the head bolts. should be torqued to about 65 ft.lbs.
Wiki User
∙ 17y ago
Add your answer:
Earn +20 pts
What are the torque specs for the rocker arm studs for a 1995 cavalier?
22 ft-lbs
What are the torque specs for 327 rocker studs?
50 lb/ft lubricated with oil. Check out the link I posted.
What are the rocker arms bolts torque specs on a 1995 Ford F-150 and inline six 4.9 300 cu?
on a '95 300 straight 6 with rocker arm bolts, not studs with nuts, the torque spec is between 17 and 23 foot lbs. if it has studs with nuts it is older and the specs are different so you will need to research that more.
What is the torque sequence for rocker arm bolts on a 1991 ford 1.9 engine?
There is no torque sequence just torque rocker arm studs to the proper torque
What is the rocker arm torque specs and sequence for a Chevy 305?
With the valve fully closed and the lifter fully at the down position, tighten the adjusting nut until there is no up and down travel in the push rod. Then tighten the adjusting nut 1/4 turn. This is only if you have hydraulic lifters. Tighten the rocker studs to 50 ft/lb of torque. These are the bolts holding the rocker assembly in place.
What are the torque specs for whell nuts on a 1979 El Camino?
80# w/7/16th studs.
What is torque spec for 1981 Chevy swbscottsdale 305 rocker arms?
Rocker studs lubricated with oil, 50 ft/lbs. Valve covers 3 lb/ft.
The torque specs for the water pump for a 1999zx2 ford escort?
The pump to studs tension is 15-22ft lb
What is the torque specs for the lug nuts on a 2003 Eddie Bauer Expedition?
100 Ft-lbs for 12mm wheel studs 150 Ft-lbs for 14mm wheel studs
How do you adjust valves on a 2.2l s10?
There is no adjustment. Rocker arm nuts/studs are torqued down to specs and that's it. If they are clattering you have worn out valve train parts.
How do you fix a rocker arm if it is loose or broken in your car?
Your best bet is to buy the manual. There are multiple ways of adjusting rockers and it depends on the vehicle. Your loose rocker arm may also be an indication of a bent push rod, bent valve, or worn out cam. there are 2 types of rocker arm studs pressed in and threaded in. if it is pressed i suggest buying the same size threaded stud, tapping the hole and using 2 stacked nuts screw it into the hole in the head. if its threaded just remove the old one and thread in the new one, be sure to check torque value for this application answer if a rocker arm is broken, u need to remove rocker cover the rocker arms are all on one tube bolted to the head remove the nuts that secure this tube slide as many rocker arms as need to get to broken rocker arm, off the tube replace with new rocker arm replace others that u needed to remove. sit tube with rocker arms back in place making sure that u align all rocker arms to the proper place tighten securing nuts to proper torque over tightening will break the studs then adjust rockers to specs if engine has hydraulic lifters you will not have to adjust replace rocker covers using new gaskets if the rocker ram is loose, adjust to specs if engine has hydraulic ligters, torque to specs job is done
What are the torque specs for 2007 96 cubic inch harley head bolts?
torque to 17ft/lbs then 90 degrees..........this is done this way because sometime studs twist
