Underneath the wiper motor assy.
You can locate your blower motor relay switch by looking at the diagram in a service manual. The blower motor relay switch should be below the dashboard on the passenger side of the passenger compartment.
right next to the blower motor I'm don't know about the 2000 model, but it is directly behind the blower motor of the 1999 Century.
on the bottom passenger side under the glove box remove the cover, locate the blower motor, disconnect the plug from it, remove 3 screws and the blower motor should come out.
The year, make and model info would help but in most cases the blower motor resistor can be found close to the heat blower motor. So locate the blower motor and the resistor should be very close to it.
trying to locate ,the resister to the blower motor foe 2003 grand prix gt
need to locate the blower motor on Mercedes 300E 3.0 motor
They generally locate the heater motor speed resistor nearby the blower motor because the resistor depends on the blower to keep it cooled.
The blower motor itself could be seized or the wire connection to the motor may be loose. The blower motor is located on the passenger side under the the dash. You will have to remove the cover just above the passengers feet to locate the blower motor. Hope this helps.
1996 Dodge Neon - the blower motor is located under the dash, behind the glove box. Removing the glove box makes things easier but is not required. 1.) disconnect the blower motor power cord. 2.) locate the retaining tab and gently pul down while twisting the blower motor housing clockwise. The blower motor will now drop out of the dash.
# Locate the blower resistor under the right-side of the instrument panel # Disconnect the electrical connector from the blower motor resistor # Remove the blower motor resistor mounting screws and remove the resistor from the housing # Installation is the reverse of removal
Blower motor is most likely dead. Locate the motor (near dash commonly) and with fan in car on , tap with hammer. If blows your motor is the prob, $50-60 for the motor and it takes about 40 min to replace.
Locate the resistor under the dash attached on the blower motor housing. Disconnect the wire harness connector. Remove the resistor and install a new one.
Blower motor fuse is blown. Blower motor resistor burned out. Blower motor switch bad. Blower motor bad.
If you are saying the blower motor will not work, then check the fuse. If the fuse is not blown, then it is possibly a defective Blower Motor Resistor Pack, blower motor, or blower motor speed control switch, in that order.If you are saying the blower motor will not work, then check the fuse. If the fuse is not blown, then it is possibly a defective Blower Motor Resistor Pack, blower motor, or blower motor speed control switch, in that order.
usually the blower motor resistor pkg. located on or near the blower motor
Blower motor: remove the glove box and you will see the blower motor and blower resistor.
It's close to the blower motor.
it's under the passanger side dash, below the glove compartment!
its under the glove conpartment. 2 screws hold it in place.
The blower motor fuse protects the blower motor electrical circuit. The blower motor relay operates only the high speed function of the blower motor. The blower motor speed resistor operates the lower speed functions of the blower motor.
Your wiring is probably messed up, happened to me. Locate the wires from the blower to the controls check them and replace as needed. Assuming no wiring problem check and replace the blower motor resistor.
The resister for the 2001 prism blower motor drops voltage to the blower motor. This is how the blower motor runs at a lower speed.
Generally the blower motor resistor is found close to the blower motor. It relies on the blower motor to keep it cool.
Defective blower motor, blower motor resistor pack, or blower motor speed control switch.
To change the blower motor resistor in a 2002 Nissan Maxima, locate the blower motor resistor under the glove compartment on the passenger side of the vehicle. There is a clip that is depressed and then the resistor will slide out. Remove both ends of the resistor and then replace with the new resistor.