Quantcast
answersLogoWhite
notificationBell

Top Answer
User Avatar
Wiki User
Answered 2015-07-14 16:48:10

There should be an illustration in your ownners manual.

Just had mine done.. mechanic had to remove psgr side motor mount to release belt. Not a fun job.

trust me this ne job you want to pay someone to do, you need to lower the engine cradle to remover the PS motor mount,

you could also visit

http://www.just .com/questions/5psw-replacing-serpentine-belt-1998

it is the same for a 97. full illustrations and step by step directions.

you will need an 18mm for the mounts and a 15 mm for the tensioner. it is an involved job but doable for the amateur. just make sure you have the engine supported and that the wood use is very important.

-------------------------------------------------------------------

This isn't a job if you aren't mechanically inclined. I didn't want to have to take the motor mount off, so I found an alternative solution, which involved me taking a reciprocating saw to the lower spacer on the motor mount so that I could slip the belt in underneath. I then used a thick washer to make the difference, and it'll allow me to easily change it in the future.

You will need some specialized tools, mainly (if I remember correctly) a reverse torx bit (just like the impression left by a torx bit). The job took me two days because I was trying to figure things out. Like the OP said, not impossible, but if you aren't sure you can do the job then you will be asking for trouble.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

Where could you find an illustration on replacing serpentine belt on 1994 Buick Park Avenue?

Try looking in either a factory service manual, a Chilton manual or a Haynes manual. If you don't have a manual your local library may have one.


Is there a separate belt other than the serpentine belt on a 1997 buick park avenue?

I have a '92 PA Ultra. The Ultra has the supercharger. There are two sets of serpentine belts for this configuration.



When Did The Buick Park Avenue Start?

The Buick Park Avenue Started In 1991


Where is the water pump on a 1992 buick park avenue located?

Passenger side bolted right to the center of the engine block behind the serpentine belt.


Where can you find a diagram for a serpentine belt for a 1995 buick park avenue?

you will find a diagram on the packet when you buy a new belt. there is also a diagram in the owners handbook




Does a 1999 Buick park avenue transmission fit in a 1995 Buick regal?

Depends on the engine the Park Avenue had in it.


Show a diagram of a Buick park avenue engine?

show a diagram of a buick park avenue crankshaft sensor


Is a 97 Buick park avenue fuel pump interchangeable?

Yes, with another 1997 Buick Park Avenue.


Can you drive a Buick Riviera without having the serpentine belt attached for the supercharger?

yes. I've had my 97 riv over 4yrs and have thrown 3 serpentine belts and have went without one for 4 months before replacing it again.


How do you replace the starter on a 1996 Buick Park Avenue?

remove the 2 bolts located on the top of the starter and remove.Do the same in reverse when replacing the new starter.


What causes bad idle in 1997 Buick park avenue ultra?

what is the down side of the 1997 buick park avenue


Will 22 inch rims fit on 2003 Buick park avenue?

Yes i have 22x8.5 on a 97 Buick park avenue


How to replace serpentine belt on 1992 buick lesabre?

Loosen the tensioner pulley on your 1992 Buick LeSabre. Take the serpentine belt off. Put the new serpentine belt on and tighten it down with the tensioner pulley.


How do you slim Jim 1992 Buick Park Avenue?

I am locked out of my Buick park avenue and have a slim Jim but don't know how to use it


Do you need a special tool to change a serpentine belt on a 2001 Buick Regal?

I need to know if I need a special to to change my serpentine belt on a 2001 Buick Regal


How do you replace serpentine belt tensioner 1998 buick park avenue?

Just did mine today. Too about an hour. Pretty straight forwar and no special tools require. Will provide photos later.


Can you SHOW me a diagram on the serpentine belt for a 1997 buick park avenue?

See http://www.mvreader.com/multiview/dayco/zoom.php?zoom_item=C0001D&l=n&catalog=auto&category=2


How do you replace the serpentine belt on a 1996 Buick Park Avenue?

You need to turn the automatic(spring loaded) tensioner to release pressure on the belt... the library may have a manual for the details free dave


How do you take the tension off the serpentine belt on 1998 Buick Park Avenue?

Put the proper size wrench or socket on the pulley of the tensioner.Pull the wrench counter clockwise to release the tension on the belt.


How do you replace a heater core on a 1994 Buick park avenue?

I need to know how do i replace a haeter core on a 1994 buick park avenue?


Tightening a steering column on a 89 Buick park avenue electra?

how do i tighten the steering column on a 89 buick park avenue electra


What is The Wiring position for the ignition module on a 1990 Buick park avenue?

what is the wiring position for the ignition module on a 1990 Buick Park Avenue?


Still have questions?

Trending Questions
How to Make Money Online? Asked By Wiki User
Best foods for weight loss? Asked By Wiki User
Unanswered Questions
How old is zak beggans? Asked By Wiki User
Does arsenio hall have ms? Asked By Wiki User