answersLogoWhite

0


Best Answer

hmmm, I've never had an oil temp sensor. I've only had an oil pressure unit, on the back of the block behind the distributor, and a block/coolant temp located on either head, one of my cars have even had one in each head. my 2cents :)

User Avatar

Wiki User

โˆ™ 2005-11-06 20:57:53
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where do you install a Oil Temp Sensor on a 350 block?
Write your answer...
Submit
Related questions

Location of temperature sensor on 5.7 350 engine?

the temp sensor is on the driver side of the engine block next to the exhaust manifold.


What sensor is located on the top of a 1988 Chevy 350 motor?

Could be the temp sensor..there could also be an oil pressure sensor at the top, back,or the block.


How do you install a temp sensor on a 350 Chevy motor?

Most of them are as simple and unbolting the old one and bolting in the new one.


Where do you install water temp sender in Chevy 350 block?

There is usually at least one or two pipe plugs in the intake manifold that can be removed.


Where do you install the oil pressure gauge on a Chevy 350 small block?

how to install the oil pressure gauge on a Chevy 350 small block


Can a water temp sensor affect the starting of a 350 Chevy engine?

No.


Is it possible to install 305 vortex heads on 350 block?

Yes their the same block....


Where is the anti knock sensor on a Chevy 350 block?

It is in front of the starter on my van.1990 350


Location temp sensor 92 350 engine?

next to the thermostat housing.


What makes a chevy performance eldblock 350 intake heat ups?

the temp of the intake manifold is controlled by the temp of the water in the block.


Does a 1979 Chevy small block 350 have a knock sensor?

no


What is the normal block temp for a Chevy 350?

195 to 210 degrees is NORMAL operating temperature.


Where do you find temp sensor on a 1987 ford e 350 with a 351?

The temp sensor is to the right of the distributor cap in the top of the manifold about 6 inches away screws into the manifold. I just replaced mine and the temp gauge now is back working


What sensor is above the starter that sits in the block on a 1993 silverado 350?

It is the knock sensor. It retards the timing if the engine pings or rattels.


Difference from a big block 350 to a small block 350?

There is no such thing as a big block 350.


What better big block 350 or small block 350?

there is no such thing as a big block 350


Where is the ambient air temp sensor on f-350 6.2 l?

It's usually one of the wires in the MAF


Is a 5.3L block the same as a 350 block?

no. a 350 block is a 5.7L


How to troubleshooting a Map sensor for a Chevy 350 small block?

get a chiltonrepair book for your car it should tell you


How can you tell the difference between A 350 small block and A 350 big block?

No such thing as a 350 big block.


The different between 350 Short block and long block?

The 350 short block has less power than a 350 long block.


350 engine out of a 1994 C1500 Can you use the block and install it into your 1975 truck?

Yes, It will work with no problems.


How can you install a big block Chevy 454 in a 1984 G20 Chevy van that used to have a small block 350?

tom bracker is tommys dad


Where connect temp sensor Chevy 350?

Most intake manifolds have 1 or 2 places to put a sensor, and you can also take a plug out of one of the heads if it's convenient.


How does a big block 350 work?

The 350 engine is a small block, not a big block.