The cable does not have any adjustment.
No cable, speedometer is electric
A Grand Caravan would have the 41TE transmission which does not have a throttle or kickdown cable.
No. The speed signal is electronic.
You will have to replace that piece of the antenna cable.
The black one is the negative.
No cable, all controls are done with electric motors.
A grand caravan would have the 4 speed transmission, which is not cable controlled. It is all electronic.A grand caravan would have the 4 speed transmission, which is not cable controlled. It is all electronic.
Follow the red battery cable to the engine, and you will find the starter. It is located on the front of most caravan engines.
The 2003 Dodge Grand Caravan starter is located on the right hand side of the engine. You can follow the positive battery cable from the battery directly to the starter.
Look at the lower rear end of engine - follow the + battery cable
Normally goes to the starter or starter solenoid.
replace spedo cable. I don't think the 96 Caravan has a cable. It has an electronic sensor but others said replaceing the sensor doesn't solve the problem.
speedometer cable is gummed up inside the housing.Remove cable from speedometer.Pull out inner cable. Lubricate with good grease and install.
Take the - battery cable off and put it back on.
They don't use linkage, they use a cable. The cable goes between the shift lever mechanism to the transmission.
To change the antenna cable on a 1998 Buick LeSabre Limited, a person has to unscrew the old antenna cable from the back of the radio. Then pull the antenna wire out from under the dash and follow it to the antenna. Unscrew the old cable from the antenna. Screw in the new cable and thread it back under the dash in the same path as the old cable and screw it to the back of the radio.
replace window regulator assembly.
It runs to the under hood fuse box, the alternator, and the starter.
reach up between the grill and the radiator/ac cooler and pull on what's left of the cable.
One may attach an antenna cable to their TV in an extremely straightforward manner. Once the antenna is set up there will be a cable on the antenna equipment that should be long enough to reach the television. The cable is then inserted to the television in the plug (port) that is properly labelled for antenna equipment.
TBS is a cable channel, you can't get a cable channel w/ an antenna.
Remove the positive battery cable from your 1997 Dodge Grand Caravan battery. Remove the cables from the starter. Remove the retaining bolts from the starter. The starter will come off.
For the 1992 and 1994 models (and likely many other years), the antenna is attached to the roof of the vehicle by two Phillips screws. After removing these screws, the unit will slide out of its hole towards the rear of the vehicle. There should be a translucent white tube where the antenna slides into and a black cable. The black cable runs through the body of the car to the back of the radio. This can be seen from the passenger's side footwell and reached from the driver's footwell. Detach the cable from the back of the radio and attach a retrieval string or twine to the radio end of the cable. Remove the antenna assembly from the car roof, allowing the retrieval line to exit out of the mounting hole. Detach the line from the old antenna cable and tie it to the end of the new antenna cable. Use the retrieval line to thread the new cable through the car frame back into the passenger compartment. Detach your guide line and plug the new antenna cable into the radio and screw the new antenna assembly into its mounting hole on the roof.
The instrument panel and the radio have to come out to replace the antenna. 1. The old antenna cable will be attached to the new cable to pull it through the mounting hole and into position. Do not pull the old cable all the way out when the antenna is first detatched. 2. Remove the instrument cluster. 3. Remove the radio. 4. Reach through the cluster hole and detatch the antenna lead from the clips. 5. Disconnect the antenna cable from the radio and detatch it from the heater box and remaining clip. 6. Remove the 2 screws that that secure the base of the antenna to the windshield pillar. 7. pull up on the antenna just far enough to expose the tape. 8. Cut the old antenna cable at the base and tape it to the radio end of the new one. 9. Remove the old antenna base and the insulating tube. 10.Guide the new antenna cable into place with the old one and install the new antenna base and tube. 11. Make sure the end of the antenna drain tube fits into it's hole, then attatch the antenna to the windshield pillar with the screws. 12. Position the antenna lead in it's clips. 13. The remainder of the installation is the reverse of the removal steps.