answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2006-07-24 21:49:33

Hidden behind the harmonic balancer. You will need a puller to remove the balancer. It will be black, a couple of inches long, with a wire coming out of it. The frame of it is usually aluminum, and adjustable. You will need an alignment tool to adjust the sensor.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


where is the oxygen sensor located on a 1997 Chevrolet lumina


The knock sensor, in your 1997 Chevrolet Lumina, can be found on the front of the engine. The knock sensor is near the top of the engine.



Just had this done on my 97, along w/ other work. It cost me around 325.00 for the crank sensor.


The 1997 Chevrolet Malibu crank position sensor is located on the back of the crankshaft. The rear engine cover will need to be removed in order to view the sensor.


Answerthe camshaft sensor is the distributor but the crankshaft position sensor is located right next to the crankshaft its held on by one bolt


Begin by removing the rear engine cover from your 1997 Land Rover Discovery. Remove the crankshaft sensor wiring harness. Remove the crankshaft sensor retaining bolts. Reverse the process to install your new crankshaft sensor.


location of crankshaft sensor on 1997 Infinity I30 is it on the engine or in the gas tank plz show a pic



It does not have a crank shaft sensor.


It is behind the harmonic balancer on the left front side of the timing cover.It will have 1 bolt that holds it in.


WOW WAY TO NAME ALL OF THEM LOL it is the crankshaft position sensor and either knocks sensor or camshaft position sensor First off if you a have a 3.1 it is the KNock Sensor. Crankshaft sensor and cam sensor is on the belt side of the motor. Crank is on bottom behind the big pully and cam is on top(half way up) usually under power steering pump


the crankshaft sensor is located behind the harmonic balancer on the ft timing cover


The timing sensor is called a Crankshaft Position Sensor (CKP). It is located at the 10 O'Clock positon on the crankshaft pulley.


The 1997 Chevy Malibu crankshaft position sensor can be found on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft position sensor.


The 1997 Chevrolet Lumina has an EPA Economy of 17 miles per gallon in the city, 26 mpg on the highway, and an average of 21 mpg.


Check the Crankshaft position sensor


on the right side of the engine


The main pulley on which the serpentine belt goes on in a 1997 Chevy Lumina LTZ is the crankshaft pulley. The crankshaft pulley plays a role in the wheels turning and powering the alternator and power steering pump.



The crankshaft position sensor is at the rear of the engine where it joins with the transmission bellhousing. It is at the left (front) side, not far from the starter.


Drain the water from your 1997 Chevrolet Lumina cooling system. Remove the water supply lines to your heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.


The crankshaft position sensor is at the rear of the engine where it joins with the transmission bellhousing. It is at the left (front) side, not far from the starter.


on the v6 1997 lumina ,the camshaft sesor is on top of engine right behind the power stiring pump,very small space just follow the four wire plug on top of engine ,plug wires lead right to sensor.i hope this helps you.


To make a crankshaft position sensor work on a 1997 Honda passport with a 1995 block and 1997 heads will take a lot of work. You will have to redo everything under the hood.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.