did you mean underneath the exhaust manifold? and when you say "front of engine block" do you mean driver's side of engine block 'cause there is a sensor down there but there is also a sensor under the intake manifold in the block next to the oil filter. Just trying to make sure. Thanks it is located on the front of the engine block, behind the exhaust manifold. There is a bolt holding it in place. it might break when trying to remove it.I used two screws into the sides of the plastic sensor housing going through a metal bracket and dobled up some tie wire around the bracket and a pry bar and was able to pull the rest of the sensor out.
Your Answer
Related Questions
Where is crankshaft sensor located and how do you change it on 1999 Pontiac Grand Prix?
there isn't a crankshaft position sensor on a 3.8l motor in a 1999 Pontiac grand prix according to the manual
Where is the crankshaft sensor located on a 1998 Pontiac Transport?
It is located behind the crankshaft pulley and requires the pulley to be removed to change it out.
How do you change the crankshaft position sensor on a 2003 Nissan Altima?
How do you change the crank sensor on a 2002Nissan Atima3.5?
How long does it take to change a crankshaft position sensor on 3.4 liter Oldsmobile?
The length of time it takes to change a crankshaft position sensor on this car depends on the people working on it. It can take 1-5 hours depending on the person(s) making the change.
Camaro 1999 z28 crank position sensor?
how do you change a crankshaft position sensor on a 1999 chevy camaro z28?
How do you change the crankshaft position sensor on a 2001 Pontiac Grand Prix?
remove the front passenger wheel, remove the crank pulley, remove the crank sensor. you may need a GM special tool to remove certain bolts
How do you change the crankshaft sensor for a 2004 crossfire?
Disconnect the negative battery cable.Remove the air cleaner housing.Disconnect the crankshaft position sensor harness connector.Remove the retaining bolt and the crankshaft position sensor.Reverse procedure to reinstall.Are the Crankshaft sensor and the Crank snsor the same?Please let me know?
Where is the crankshaft position sensor on a 1999 Grand Prix GTP and how do you change it?
The crankshaft position sensor is located behind the crankshaft pulley and harmonic balancer. A writeup of how to remove with pics can be found in the article for a camshaft install. check out: http://www.clubgm.com/cam Hope this helps. "G"
How can you change your Crankshaft position sensor on a 96 Acura Integra?
change your distributor. its just a part inside there next to the ignition coil
How long does it take to change a crankshaft position sensor on a 2000 olds intrigue?
Took me about an hour to change mine, but it was the first time.
Do you have to get under the car to change the crankshaft on an 04 pt cruiser?
You have to remove and disassemble the engine to replace the crankshaft.If you mean the crankshaft position sensor, then yes. You access it from underneath. It is just above the oil pan on the back of the block.You have to remove and disassemble the engine to replace the crankshaft.If you mean the crankshaft position sensor, then yes. You access it from underneath. It is just above the oil pan on the back of the block.
Can you change the distributerless on a 1989 Chevy Celebrity?
You can replace the ignition control module and the crankshaft position sensor as required.
Where is the crankshaft position sensor on a 1999 Chevy Venture and how do you change it?
Where is the camshaft sensor located in 1997 Chevy venture
How do you change the crankshaft position sensor on a 2000 Dodge Neon?
Take off the old one and put the new one on.
How do you change crankshaft position sensor?
where is the crank shaft pistion sensor located on a 2002 Chevy Malibu, and how hard is it to replace
Where is the crankshaft position sensor located on a 1996 Dodge Ram 2500 with the 318 engine?
the crankshaft position sensor is located in between engine and trans passenger side. it easy to change . It is in the top of the bell housing on the pass side, under the trans dipstick tube.
Where is the crankshaft position sensor on a 5.3 liter?
It is above/behind the starter. The starter must be removed in order to access the sensor to change it.
How do you change crankshaft position sensor on 04' aerio?
remove the engine and transmission from the car, then remove engine flywheel and it will be right there
Location for 2003 optima crankshaft position sensor?
it is behind the timing belt when changing this you should change the balance belt also the timing belt
How do you change a crankshaft position sensor on a 1997 Pontiac Grand Prix SE?
The Crankshaft Posistion Sensor (CPS) is located behind the harmonic balancer. This needs to be removed to access the CPS. Check out the following website for instructions on how to remove the harmonic balancer. http://mykidz.net/GTP/CrankPosSensor.shtml Hope this helps. "G" P.S. After replacing the CPS you will need to do a Case learn (or crankcase learn)..This is a procedure to set the sensor to identify the correct cylinder relative to the crank position. If you cant or dont know how to do this take your car to a professional.
How do you change the fuel pump in a 1999 s10 4cylinder?
Remove the fuel tank or remove the bed, your choice.
Where is the crankshaft position sensor in a 1997 ford explorer?
It's down underneath the engine right next to the pully in front of the crankshaft. It's a pain to change because one of the two bolts is almost impossible to get to. Have fun with that good luck.
How do you a change a battery in a 2002 Pontiac Montana?
how do you change a battery on a 2002 Pontiac Montana
Where is the crankshaft position sensor on 2001 intrigue?
The crankshaft position sensor is near the front of the motor behind the starter. you need to remove the starter to change it. Here is a picture for the 3.5L : http://im1.shutterfly.com/media/47a0df00b3127ccef97e38181be400000030O08IZtXLZszag9vPhI/cC/f%3D0/ps%3D50/r%3D0/rx%3D720/ry%3D480/
Can you change the crankshaft sensor without having to change the whole distributor on a 1998 Chrysler cirrus?
The crank sensor is not in the distributor, it is in the top of the bell housing. The cam position sensor is in the distributor and is not available separately
Car Computers and SensorsOldsmobile Cutlass SupremeNissan AltimaOldsmobileCrankshaft SensorsChryslerFormula OneOldsmobile IntrigueChrysler PT CruiserChevy CelebrityChevy Venture2000-2005 Dodge & Plymouth NeonsBuick Park AvenueDodge RamChevy SilveradoAuto Parts and RepairsSpark Plugs and WiresFuel PumpsFord Explorer LimitedCar BatteriesChrysler Cirrus
