answersLogoWhite

0


Best Answer
Copy

The EGR valve On the 4.3 engine vin W It's right below the air intake on the intake manifold. Mounted with two bolts, and has one electrical connector (4 wires) I have a 94 s-10 that for the last week is acting like a Ford (fix and repair daily). Symptoms are rough idle, lurching when the RPM's drop below 1.2k, loss of POWER brakes when rolling up to a stop sign and service engine soon light. When you check the codes it gives a 32. Found that pieces of loose carbon the size of small stones are getting caught between the valve and valve seat not allowing it function correctly. I

User Avatar

Wiki User

โˆ™ 2005-03-25 00:08:41
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: Where is the ERG valve located on a 1996 Chevy S-10 pickup?
Write your answer...
Submit

Related Questions

Where is the PCV valve on a 1996 Chevy Camaro 3800 v6?

On a 1996 Chevy Camaro, the PCV valve is located on the right side of the valve cover. There is a hose that runs from the PCV valve and connects to the back of the intake manifold.


Will a steering wheel from a 1996 Chevy pickup fit on a 1970 Chevy pickup?

NO it will not.


Where is the PCV valve on a 1996 Chevy Tahoe located?

It is in a hose that is stuck in the top of the drivers side valve cover.


Where is the EGR valve located on a 1996 Chevy Silverado?

It is in the middle between the intake and the water pump.


On a 1996 Chevy Suburban the brake system incorporates a dump valve What does this dump valve do and or where is it?

The brake dump valve on a 1996 Chevy Suburban is used for bleeding the brakes after new brake pads are installed. It is located on the master cylinder for each brake.


Where on a 1996 Chevy pickup 4.3?

Where what! What is your question?


Where is the ecm located in a 1996 Chevy s10 pickup?

Under the hood, on top of the passenger side inner fender.


Where is the starter located on a 1996 Chevy Cheyenne pickup?

Try the lower rear of the engine - try to follow the + battery cable


1996 jimmy evap purge valve sensor where located?

where is the evap purge valve located in a 1996 jimmy


Where is the alternator located on 1996 Chevy s-10 pickup truck?

You would find it in the front of the engine driven by the accessory belt.


Where is PCV valve locate on 1996 s-10 pickup?

On top of the valve cover on the passenger side


Will a 1996 Chevy s-10 4x4 transmission fit a 1996 Chevy 4x4 1500 pickup?

NO it will not. The bell housing is different.


Which valve do you use to add freon to a 1996 Chevy Blazer?

It should be the valve located on the condensor. The charger should only fit one valve. You can pick up a kit a your local parts store.


Will a 1996 Chevy Tahoe 350 engine fit a 1988 Chevy pickup?

Yes but modification will be needed


Where is the egr valve located on 1996 Mitsubishi galant?

The EGR Valve on the 1996 Mitsubishi Galant is located underneath the Exhaust Manifold.


Where is the EGR valve on a 1996 Mazda Protege?

Where is the EGR Valve on a 1996 Mazda Protege located at?


Where is the 4 wheel drive actuator located on a 1996 2500 Chevy pickup?

It is screewed into the front Differential, towards passenger side but in the middle of the housing.


What size motor is in a 1996 Chevy Silverado 1500 Pickup?

The Chevy SBC 5.7L 350cid V8 was the standard


Where is the fuel filter located on a 1996 Chevy S-10 pickup 4 cylinder?

right side along frame rail.It is an in-line filter.


Where is the expansion valve on a 1996 maxima located?

No


Where are the PCV valve and the fuel filter on a 1996 Chevy Cavalier?

The PCV valve is internal and shouldn't need to be replaced. The fuel filter is located at the rear of the car. It is by the fuel tank and rear axle.


Where do you find the modulator valve on a 1996 Chevy Corsica?

on automatic transmission


What kind of engine in 1996 Chevy 1500 4x4 pickup?

5.7 liter vortec.


How do you change a striker bolt on a 1996 Chevy pickup?

It just unscrews, It is real tight.


Where is the PCV valve located on a 1996 Chevy 305?

Usually on one of the valve covers attached to a rubber hose going to the emissions system. the valve covers are the "upside down bread pan" looking things on both sides of the engine.