The 4 cylinder 1994 Ranger uses a MAF sensor, not a MAP sensor. It is located very close to the air cleaner. Air flows through the air filter, then past the MAF sensor, and then into that long, odd-shaped black plastic tube to the throttle body. You can find the MAF sensor very easily by locating the air filter and then looking for an electrical fitting with some wires going to it. If you remove the MAF aluminum-body sensor..the only thing you can do for it is clean it; CAREFULLY spray some of Radio Shack's Tuner cleaner into the open port in the middle. DON'T STICK any objects down there as you can break the heating element inside the port. Use only a cleaner that leaves no residue and after let dry 15-20 min. If your truck does have a MANIFOLD ABSOLUTE PRESSURE (MAP) sensor it should be on the intake manifold or connected to it.
The 1994 Ford Ranger pickup truck map sensor is located behind the dashboard, on the passenger side of the passenger compartment. The map sensor is contained in a dust free box.
It should be located in the oil pan. On my ranger its on the drivers side.
looking for an answer to this question "Where is the MAP sensor located in a 6 cylinder Ford ranger 1994 Help! www. motorcraft. com (no spaces) does not list a MAP sensor , it shows an AIR MASS SENSOR which I assume is the MASS AIRFLOW SENSOR which would be mounted close to your air filter housing
I'm not a mechanic / technician but the engine wiring schematic for the 3.0 liter V6 engine in a 1994 Ford Ranger that is in my Chilton's repair manual does not show a knock sensor
The 2002 Ford Ranger camshaft position sensor is located on the back of the camshaft. The rear engine plate will need to be removed in order to view the sensor.
Where is the crank sensor located on a 94 ranger 4.0 motor
According to www . motorcraft . com ( no spaces ) the IAT sensor is a thread in type for the engines in a 1994 Ford Ranger - so threaded into the upper area of the intake manifold somewhere
On the engine.
The 1998 Ford Ranger speed sensor ring can be located on the passenger wheel. The speed sensor ring will be on the inside of the brake rotor.
The map sensor is located on the intake manifold of a 1994 Ford. It could also be located on the plenum by the throttle body.
under the hood driver side
Look by the balancer.
The 1999 Ford Ranger 3.0 liter engine throttle positioning sensor is located on the cylinder head. The sensor will be near the middle of the cylinder head.
I'm not a mechanic / technician but the engine wiring schematic in my Chilton repair manual for the 2.3 in a 1994 Ford Ranger does not show a knock sensor
There is no such thing as an oil pressure switch on your 1994 Ford Ranger 3.0 liter engine. There is an oil pressure sensor. The oil pressure sensor can be found on the left-hand side of the engine.
Where is the ford ranger 2004 revcounter sensor conected
the o2 sensor is located on the exaust manifold
What model year? The earlier 2.3L did not have a MAP sensor.
According to my Chilton repair manual engine wiring schematics there is ( 1 ) on the 4 cylinder and ( 2 ) for the V6 engines in a 1994 Ford Ranger
It's located with the MAF
The 1994 Ford F1 50 crankshaft sensor is located on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft sensor.
I don't know if it is the same as the Ford Mustang , but the BAP sensor was mounted on the firewall - good luck
I'm not a mechanic / technician but my Chilton repair manual does not show a knock sensor in the engine wiring schematic for the 2.3 liter 4 cylinder in a 1994 Ford Ranger
The speed sensor is located on the differential (rear end) I have a 99 Ford Ranger and have recently replaced one. EASY! Good luck!
It is located between the distributor at the back or the engine.