Best Answer

Either in the exhaust manifold or the exhaust pipe right below the manifold. GoodluckJoe

User Avatar

Wiki User

โˆ™ 2004-08-18 10:47:28
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the O2 sensor on a 2.3L 96 Ford Ranger?
Write your answer...
Related questions

What are the timing specs for a 96 Ranger 23L SOHC 4 cylinder and will the crankshaft position sensor cause it not to crank?

haha i asked this question and i can answer it now. I finally got my truck on the road !!

How do you fix trouble code PO340 Camshaft Position Sensor Circuit Malfunction for a 96 ford ranger?

get a new cam position sensor (about $35)

Where is the crankshaft position sensor on a 96 Ford Probe SE?

"Where is the crankshaft position sensor on a 96 ford probe SE?"

Where is the camshaft position sensor on a 96 ford ranger 4-cylinder?

The camshaft position sensor is on top of the engine. It is on top of a shaft in the same place that older rangers had a distributor.

What are the causes for no heat problems on a 96 ford ranger?

no heat in 96 ford taraus,new thermostat,has coolant in it

What does air bag code 44 mean on a 96 Ford Ranger?

right hand radiator primary crash sensor not mounted to vehicle properly

How do you change a fuel filter on 1996 Ford Ranger supercab?

where is the fuel filter located on 96 ford ranger supercab

What would cause your 96 ranger 23l to backfire through the breather?

More than likely it has jumped time. This is a comman problem with older timing belts. Or in colder weather.

How do you adjust a clutch on a 96 ford ranger?

it is hydraulic. there is no adjustment

What is interchangeable with a 1996 Ford Ranger?

a 96 Mazda pickup

How much does a 1996 Ford Ranger weigh?

A '96 ranger weighs around 3,245 pounds

Where is the bank 2 sensor 1 o2 sensor on a 96 ford ranger?

bank 2 is the drivers side of the engine on a Ford V6 ( rear wheel / 4x4 ) sensor 1 is in the exhaust system before the exhaust enters the catalytic converter sorry , I can't be any more specific

96 ford ranger what type of spark plugs should i use?

Motorcraft is best for Ford

Will a 87 ford ranger transmission fit into a 96 Mazda b2300?

What make and model ford 6 cyc will fit 96 mazda

Why won't the 4x4 engage on a 96 ford ranger?

Vacuum hose disabled.

What is the horsepower in a 2.3l manual transmission on a 96 Ford Ranger?

For a 1996 Ford Ranger , 2.3 litre four cylinder engine ( 112 horsepower from the factory )

What causes your 96 ford ranger 2.3 to ping under load it does it going up a small incline?

Bad fuel, worn spark plugs or wires, dirty mass airflow sensor. Incorrect air/fuel ration, o2 sensor, knock sensor.

Were is the door chime sensor located on a 1996 Ford Ranger?

The door chime switch on a 96 ranger is part of the door latch mechanism. If your door chimes all the time when your driving try spray lube on the latch that should free it up.

Where is a ford overdrive sensor on a 96 explorer?

The 1996 Ford Explorer overdrive sensor can be found on the right hand side of the transmission. The overdrive sensor will be near the front of the transmission.

How do you use a hanger to open the door of a 96 Ford Ranger?

stealing is against the law

How do you install a lift kit on a 96 ford ranger?

The kits usually come with instructions

What does the number 1 fuse on a 96 Ford Ranger go to?

According to the 1996 Ford Ranger Owner Guide : ( the # 1 fuse is a 7.5 amp fuse for the power mirror )

Where is the AIT sensor in a 96 Ford Thunderbird LX 3.8?

right before the mass air flow sensor

Ignition is lock and wont start 96 ford ranger?

If the ignition is locked and the 1996 Ford Ranger key will not turn, there could be a problem with the transmission sensor that lets the ignition sensor know that the car is in Park. Try shifting into neutral with the foot on the brake, then turn the key. If the key turns, the sensors are bad. If the key does not turn, try wiggling the steering wheel while turning the key.

1997 2.3 Ford Ranger timing marks location?

I have a 96 ford ranger 2.3. On the crank timing, does the mark on the plastic cover TC mean top dead center?