answersLogoWhite

0


Best Answer

Answer: On an S-shaped hose which is behind the distributor on the driver's side of the engine. Easier access is available by loosening the alternator and removing the belt and the lower bolt. Pivot the alternator to the top on the upper bolt and retighten the upper bolt to keep the alternator up out of the way. Don't forget to remove check and clean the little canister at the other end of the S-shaped hose. This is easier if you remove the oil filter first. Make sure you get this canister back into the hole in the block straight and tight. Then you can re-install the filter and lower the alternator and re-install the belt and lower bolt.

User Avatar

Wiki User

โˆ™ 2014-11-07 22:30:46
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the PCV valve located on a 1988 Ford Ranger with 2.0 4 cylinder?
Write your answer...
Submit
Related questions

How do i repair the slave cylinder on my 1988 Ford Ranger?

The slave cylinder on a 1988 Ranger can not be repaired. The cylinder will have to be replaced, then the system bled.


Where is the pcv valve on a 1988 200sx 4-cylinder?

PCV valve is under the induction system


Where is the pressure differential valve located on a 1988 f-250?

assume you mean Brake PDV... is located on the frame directly below the master cylinder.


Where is the PCV valve on a 1988 ford ranger 2.9 liter lacated?

It is located behind (toward the rear of truck) The oil add chamber on the passanger side valve cover. Pull the hose out of the valve cover and there you'll find the PCV Valve


How do you set the timing belt on a 1984 Ford Ranger 20L?

How do you set the timing on an 1988 ford ranger 4 cylinder


What size spark plugs for a 1983 Ford Ranger XLT 4 Cylinder?

i have a 1988 ford ranger xlt 4 cylinder and my spark size is 42-46 hope this will help


What engine is in a 1988 Ford Ranger?

The 2.0 liter 4 cylinder , the 2.3 liter 4 cylinder , or the 2.9 liter V6


V6 2.9L Ford Ranger 1988?

Yes , there was a 2.9 litre V6 engine available in a 1988 Ford Ranger , as well as the 2.0 and 2.3 litre four cylinder engines


Where is the PCV valve on a 2.0L 1988 Ranger?

Coming out of intake manifold and going into rocker cover


Where is the map sensor located on a 1988 ford ranger 2.9l?

On the engine.


Where is the fuel filter located on a 1988 ford ranger 2.9 6 cylinder 4 wheel drive?

hi, I have this same truck, It is located on the inside of the driver's side frame rail around the driver door area.


Where is the external fuel pump located on an 1988 ford ranger 4x4 xlt?

The external fuel pump of an 1988 ford ranger 4*4 xlt is located inside the fuel tank or gas tank.


Where is the clutch bleed valve on a 1988 ford f-150?

On the clutch slave cylinder


Where is the horn located on a 1988 Ford Mustang LX convertible 4-cylinder?

The horn are located in the driver side front fender


Where is the starter located on a 1988 Ford Ranger truck?

Lower rear end of the engine


Where is the fuel pump on a 1988 Ford Ranger 4-cylinder?

If fuel injected - in the fuel tank If not in the front lower section of engine - follow fuel line


Where do you put the clutch fluid in for a 1988 ford ranger What does the reservoir look like?

Should be on firewall next to master cylinder


Where is the slave cylinder on a 1988 ranger four wheel drive with 2.9 liter engine?

The slave cylinder for a manual transmission hydraulic clutch is inside the manual transmission bellhousing


What is the stock cylinder compression on a 1988 V6 2.9L ford ranger?

Highest and lowest cylinders should not exceed a 10% difference


Where is the starter located on 1988 dodge Dakota 4 cylinder?

It is under the intake manifold.


Where is the starter solenoid located on a 1988 Ford Ranger?

It should be attached to the short positive battery cable.


Where is the voltage regulator located in a 1988 Ford Ranger 4x4 V6 extended cab?

inside the alternator.


Where is the voltage regulator located in a 1988 ford ranger?

According to my Chilton Guide, attached to the back of the Alternator


What is the firing order for a 1988 Ford ranger 2.9L V6?

Answer1-4-2-5-3-6 Distributor rotates clockwise. Number 1 cylinder is located passenger side front of engine. Number 4 cylinder is on the driver side front. 3 located passenger rear of engine and 6 is on driver rear of engine.


Is there PCV valve on a 1988 4 cylinder Camry?

No, on the 3S-FE there is no PCV valve or grommet. This is the 4cylinder model. The camry V6 of the same year on the other hand, does utilize a PCV valve in its crankcase ventilation system.