answersLogoWhite
Honda Civic
Honda Civic EX
Honda Civic LX

Where is the PVC valve on a 1996 Honda Civic LX?

117118119

Top Answer
User Avatar
Wiki User
2005-02-03 13:15:39
2005-02-03 13:15:39

Just in front of the air filter, there is a metal pipe with rubber hoses on each end (the breather hose). Just under the bend in the pipe, there is another small black hose (a few inches long). This hose connects the intake manifold to the PCV valve, which is located on the back of the eninge just under the intake manifold. Just follow the hose.

1

Related Questions

User Avatar

Where is the PVC valve on a 2002 Honda Civic EX?

User Avatar

Unplug old one from hose,install the new one.

User Avatar

the PVC valve is by the condigulam and to find that you need to eat crap

User Avatar

The 1983 civic, hatchback with 1.5 engine does not have one.

User Avatar

im not sure on a 1990 but on my 93 civic ex 1.6 vtec the PVC valve is on the intake right under the fuel rail

User Avatar

My 1998 Civic EX engine (CA emissions) vents the upper valve cover into the air intake for combustion. I could not locate a traditional Positive Crankcase Ventilation (PVC) valve on my vehicle.

User Avatar

The PVC Valve is most easily seen from under the car. It is to the Driver's side of the Oil Filter. You can see the hose coming down from the throttle body. This is a metal PVC valve that threads into a port on the block. It can be accessed from above by moving the throttle cables and such aside. F. Bryan

User Avatar

where dose a pcv valve go no 1996 buick lasaber...

User Avatar

location of the pvc value 2006 honda crv

User Avatar

Generally you will find a PCV valve somewhere on one of the valve covers, with a hose the connects to it.

User Avatar

The PVC valve is located at the tip of the small hose plugged into the top of your valve cover. It is located between the manifold and the top valve cover.

User Avatar

Standing in the front of your car facing the engine, in the middle of the valve cover on the left side (covered by black plastic). Remove that black plastic cover and you will see the PVC valve on the left side of the valve cover.

User Avatar

Check the engine and under the car from front to back for any oil. It is either a leak or being "blown out." If the PVC valve is stuck, or the dipstick isn't seated right oil can leave the engine block, seemingly disappearing. The PVC valve is the most likely place to start looking.

User Avatar

ware is the PVC valve 2002 deville

User Avatar

To change PVC valve on a 1993 Nissan 300zx, first remove the oil dip stick and remove the tension clip from the PVC valve hose. Then remove the hose and the old PVC valve. Replace with a new PVC valve.

User Avatar

Pontiac PVC Valve is located on the Driver's side rear valve cover.

User Avatar

A PVC Valve shuts off water A pcv valve is for positive crankcase ventilation in an engine

User Avatar

I don't have pics ,but, the PVC on my 99 Si is at the back of the engine between the oil filter and the engine.very difficult to change and see.the oil filter should be removed to make it easier.my engine is D16Y8.I imagine yours is the same.

User Avatar

where is the pvc valve located on a 1980 olds cutlass 3.8 v-6

User Avatar

where is the PVC valve on chevelet impala 2003

User Avatar

The PVC valve on a 2000 Maxima is located in the rear valve cover just behind the throttle body. REMOVAL # Grasp the PVC valve and pull it out of the valve cover

User Avatar

Ford hid the PCV underneath the intake manifold, in the rear of the passenger side valve cover.

User Avatar

Where is PVC valve located on 2008 Taurus

User Avatar

PVC Valve Removal & Installation # Disconnect the oil separator hose from the PVC Valve. # Remove the PVC Valve from the grommet in the crankcase. Grasp the valve and gently remove it from the grommet in the passengers side valve cover. Remove the valve from the hose by carefully twisting it out. # Inspect the grommet for deterioration. To Install; # If necessary, replace the crankcase grommet. # Install the PVC Valve. # Install the hose.

User Avatar

PVC Valve Removal & Installation # Disconnect the oil separator hose from the PVC Valve. # Remove the PVC Valve from the grommet in the crankcase. Grasp the valve and gently remove it from the grommet in the passengers side valve cover. Remove the valve from the hose by carefully twisting it out. # Inspect the grommet for deterioration. To Install; # If necessary, replace the crankcase grommet. # Install the PVC Valve. # Install the hose.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.