0
The blower motor resister is usaully located close to the blower motor, either under the dash or under the hood on the firewall. It all depends on your year, make and model.
i have a 2004 trailblazer
Wiki User
∙ 13y ago
Wiki User
∙ 15y agoinside the blower housing. There is a phenolic block screwed to the blower housing, it has the wires for the intermediate speeds on it. It is more likely that the switch in the dash is burnt out. A quick fix for heavy duty snow plow use is to run a hot wire from the batt to a heavy duty switch under the dash, then to the hot lead of the blower. Control the temp with the temp slider in the dash. You didn't really want fifteen amps of power going through your fuse block and ignition switch anyway, did you? Don't forget to turn it off when you park it.
Wiki User
∙ 17y agoOn my 1994 RH Drive, it's located on the passenger side, in the duct on a shield.
Add your answer:
Earn +20 pts
What will cause your ac and heater to stop working it do not even blow?
Blown fuse, bad heater blower motor control switch, bad blower motor, or a bad blower motor resistor pack.
Why the Blower motor not work on high speed on a jimmy 97?
If the blower works on slower speeds only I would suspect the high speed blower motor relay (under the hood in the power distribution box) or the switch itself. The blower speed resistor is working if all the slower speeds work.
Where is the blower motor resistor on a 2002 Oldsmobile Intrigue?
It is on the evaporator case and is held in with 2 screws.
Where is the blower resistor located on a 97 cadillac?
Blower motor speed resistors are generally located close to the blower motor.
What would cause blower motor to work on high only on a 2002 Dodge Durango?
either the control head is bad or there is a blower motor resistor that is bad.
Does 2001 dodge durango have a blower motor or is it called a blower motor resistor?
Your truck has both. the resistor is between the switch & blower.thje resistor controls the blower speed
On a 300m the blower is stuck on high and can not be controlled with the switch is there a sensor for the blower to control it?
There is a Blower Motor Resistor Pack. Either the blower motor speed control switch itself is defective or the Resistor Pack is bad.
Blower motor only runs on high?
Bad resistor at the blower motor? Bad blower motor switch?
How do you replace the blower fan resistor on a 2003 buick rendezvous?
where is the switch resistor on 2003 buick
Why is your heater blower not working?
Blown fuse. Burned out blower speed resistor. Faulty blower switch. Bad blower motor.
What controls blower on 2000 mercury villager Estate?
The blower is controlled by the blower switch, blower resistor, and relevant power relay.
Blower will not blow fuse is good?
Defective blower motor, blower motor resistor pack, or blower motor speed control switch.
Only high-speed on fan was working now it doesn't is it the switch or the blower and how can you tell which one it is?
It is most likely a bad blower motor resistor. Replace the resistor. If the problem continues, it could be the switch.
Heater fan switch works only on the highest setting?
The blower motor speed resistor is burned out. You can replace only the resistor but the resistor probably burned out because the blower motor is going bad. If you want to fix it for good, replace both the blower motor and blower motor speed resistor.
Heater blower motor not working?
the switch, or the blower motor resistor, or blower motor usually it the last two at one time
You replaced your blower motor on a Ford F 150 and the wiring harness was connected to another resistor switch What was it connected to r?
The wiring harness on a blower motor for a Ford F150 is connected to the blower itself and the resistor switch that is under and/or behind the glove compartment on the vehicle. This resistor switch is a set of 3 or 4 wires connected by a plastic clip.
How do you test a resister in a blower?
To test the blower motor resistor, unplug the resistor connector. Each blower motor switch input terminal on the resistor must have continuity to the resistor output terminal, which is connected to the circuit going to the blower motor. If the blower motor resistor continuity does not check OK, replace the faulty resistor.You need a multimeter to test the resistor block and there should be continuity between all terminals.
