Mitsubishi Montero, Pajero, and Shogun
Home Electricity
New Electrical Work
Modification of Old Electrical Work

Where is the best place to connect the red green brown and yellow wires for a trailer on a 1998 Mitsubishi Montero which has the wiring harness under the rear seat and no obvious matching wires?

123

Top Answer
User Avatar
Wiki User
Answered
2009-02-25 18:30:38
2009-02-25 18:30:38

The best place is to take off the rear taillights and wire into them with splitters.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Begin by removing the middle of your 1992 Mitsubishi Montero steering will. Remove the wiring harness. Remove the steering wheel retaining bolts.

Connect the wiring harness to the back of your 2003 Mitsubishi Lancer CD player. Secure the CD player with the retaining bolts. Connect the ground wire.

The 2002 Mitsubishi cigarette lighter is held in place with a retaining ring. Remove the retaining ring. Pull the cigarette lighter out. Remove the wiring harness from the end of the cigarette lighter. Reverse the process to install the new cigarette lighter.

go to www.autozone.com and look at repair manuals. http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800ad82a

Six-year the oil pressure gauge for your 1999 Mitsubishi eclipse with the retaining screws. Connect the oil pressure gauge wiring harness.

I do believe it's located immediately by the crank, which you can reach by removing the AC bracket, pulley bracket, and timing belt cover, which are all located on the front of the engine. You will see a wire harness connected to it leading to the top of the engine.

You can buy a speaker harness. An adapter that connect the positive and negative from the speaker into the stock harness.

Take the inside door panel off disconnect the wires for the window and door locks(if you have power windows and locks). Unbolt the door at the hinge and your good to go If you are swapping your door with a used door that has a good wire harness, when you unbolt the door at the hinge, pull the wire harness from the "a" pillar and disconnect the two plugs there. No need to disconnect each plug then re-run the harness through.

Simply remove the taillights and tap into the harness on each side as required. Then just run the wires along the molding then behind the bumper skin to the bottom near your spare tire.

can you used a 2.0 liter complete witing harness for a 2.4 mitsubishi eclipse spyder engine

You need to remove the dash panel. It will allow you to get access to many connectors and it will be easier to remove the harness.

You need a DIN removal tool, found at any auto parts store. While you're there, you'll also need a wire harness for the new stereo, possibly an adapter kit, some butt connectors and maybe a krimper. Expect to spend close to $40 for these items. Connecting the wire harness to the stereo is as easy as color matching. Slide the stereo sleeve into place, connect the harness and slide the stereo in.

Connect the sunroof motor with the sunroof motor retaining bolts. Connect the sunroof linkage. Connect the wiring harness to the back of the sunroof motor.

Usually when you get the radio the place you bought it will have a wiring harness that will fit the car. If not then go to a radio installation shop and ask for one. This will then plug right into the factory car harness and then you connect the radio to this harness. That's it. Good luck.

go to wal mart and get the wire harness it will tell you what goes where.

You need to get a special harness if you do not want to cut the wires. If you need have infinity system you will need a special harness (see the link below).

The wiring harness is a bunch of wires together running from the ecu and tcu to all of the components under the hood. If you need to remove the harness, I warn you, its a pain in the butt. If you are going to remove it, you can email me and I will be glad to go through step by step instructions.

Begin by removing the wiring harness from your 2002 Montero blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install your new blower motor.

You will need a special wire harness. You can get it along with instructions and support at http://www.crutchfield.com/

Power steering power steering pressure switch is a part of power steering pump. There is wire harness connect to the pump, it's connect the switch. Find the harness you will find the switch.

try this sight for the harness: www.scosche.com/products/sfID1/151/sfID2/158 but make sure you call and talk to a support adviser to make sure you get the right one. If you have a round port on the back of your system you will need a the right harness as it supplies power to the power amp otherwise you will not get any power to you speakers. But you may also run into another problem...some Mitsubishi systems have anti theft devices built into them and to obtain the "unlocking procedure and code" you will have to contact Mitsubishi.

it could be wires in the harness try to check them a new harness cost around 1000 dollars

No. You buy a waring harness and connect it to the car wiring and the amp to the speakers there behind the radio.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.