Heater Cores and Blower Fans
Oldsmobile Intrigue
VW Jetta
Ford Ranger XLT

Where is the blower motor resistor located on a 1999 Oldsmobile Intrigue 3.8?

303132

Top Answer
User Avatar
Wiki User
2004-10-29 10:53:44
2004-10-29 10:53:44

On the evaporator case.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

I have a 98 olds intrigue and the blower motor resistor is located under the glove box behind the blower....

User Avatar

A blower resistor can be replaced, in your 2002 Oldsmobile, by removing the resistor wiring. Remove the retaining screws. Reverse the process to install the new resistor.

User Avatar

They are generally located close to or near by the blower motor.

User Avatar

The blower motor fan cools the resistor so the resistor is usually located close to the blower.

User Avatar

where is the blower motor located a a 1997 oldsmobile achieva

User Avatar

The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it. The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it.

User Avatar

There is none - usually it is the module in the top of the heater / blower box (resistor module) that is the problem.

User Avatar

where is the blower motor resistor located on 2002 gmc envoy?

User Avatar

You have a bad blower resistor. it is located directly behind the blower motor on the passenger side of the vehicle. You must first disconnect blower motor from bad resistor. Lower and remove blower. It won't be easy but remove the screws holding the resistor, disconnect the resistor and remove it. Cost is approximately $40 for a new one.

User Avatar

the resistor is located in the blower module which is located under the hood by the a/c evaprator case

User Avatar

Resistor is located behind the blower motor assembly.

User Avatar

If the heater fan works on all speeds, then the blower motor, blower fuse, blower relay, and blower motor resistor pack are all good. If the fan runs but nothing comes out of the vents, you have a 'mode door' issue (which might include a bad control head).

User Avatar

The heater blower in a 2001 Hyundai XG300 is located on the passenger side of the engine. The blower resistor will be located on the firewall.

User Avatar

The blower motor resistor is generally located close to the blower motor.

User Avatar

The blower motor resistor is located under the glove compartment in a black shroud.

User Avatar

The 2001 Nissan Quest blower motor resistor is located on the firewall in the engine compartment. The blower motor resistor will be on the passenger side of the firewall.

User Avatar

try changing the fuses for the blower or maybe the motor blower itself or the blower resistor.....................

User Avatar

i had a 03 Chevrolet Colorado, and the resitor was located under the glove compartment, where the motor blower is, the resistor is screwed to the side of the blower. hope this works for you. the resistor is usually located there.

User Avatar

Blower resistor is under Drivers' side of center console

User Avatar

where is the heater blower resistor in a 2003 Honda element

User Avatar

The blower resistor for a 2003 Trailblazer is located under the passenger side of the dash.

User Avatar

Blower motor speed resistors are generally located close to the blower motor.

User Avatar

Hi, I just replaced the resistor on my '98 Intrigue- it's quite possible they are located similarly. The resistor is located under the dash on the passenger side, right behind the blower. I had to pull the blower out to gain better access to the resistor assembly. There is a short cable assembly that connects the resistor to the blower so if you look for the two wires that come out of the back of the blower they should lead you right to the resistor. The resistor is very hard to get to because of the hex head screws being right up against the floorboard but you only need to loosen the two back screws and remove the one in front to be able to pull the resistor assembly out. If you can get a small 5/16" socket on the screw heads you should be able to loosen them enough. There will be a larger cable assembly plugged into the resistor also. The whole procedure took me about a half hour, not a bad job but just hard to maneuver down there. !


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.