The cam sensor is the distributor.
The 1993 Chevy S 10 Blazer 4.3 liter engine temperature sensor can be grounded to the engine block. You can use the temperature sensor retaining bolts to ground the temperature sensor.
does not have one just a map sensor
The 1993 Chevy S 10 Blazer IAT sensor can be found on the top of the transmission. The IAT sensor will be near the front of the transmission.
May be computer controlled and not adjustable
In the right upper side (passenger side) of engine block.
Where is oxygen sensor on 4.3 liter 1995 Chevy S10. All O2 sensors are threaded into the exhaust system at various points, and you probably have more than one sensor.
The 1994 S10 uses a MAP sensor, not a MAF sensor. We need to know size engine you have in that S10.
throttle positioning sensor, egr, idle air control
My 1989 chevy s10 doesn't accelerate quckly,why is this?
That would be the engine coolant temp sensor for the dash gauge only. The sensor near the thermostat housing is the engine temp sensor for the ECM.
Temp sensor for the gauge.
Is there a way to bypass the ECM in a 1993 chevy s10 4.3 vortec
Was not used in that year.
there is no such thing as an egr position sensor
The coolant temp sensor on a 2003 Chevy S10 V6 is located on the front of the intake manifold. To replace simply unscrew the old sensor and screw on the new one.
On the side of the drivers side cylinder head, between #1 and #3 spark plugs.
There was no 2.8 Liter V6 installed in a 2001 Chevy S10. I posted a link of firing orders that year.
on the top of the intake
Need to know what engine it has.
Depends on which engine it has and what year it is.
Haynes makes a manual with the wiring schematic for the O2 sensor on a 1991 Chevy Blazer S10. The manual can be found at most book stores.
That should be the sensor located after the catalytic converter.
A bad engine temp sensor can do that.
It should be located along side of the thermostat housing. The electrical plug attached should have 2 wires.
If that S10 has a 4.3 engine, I find it best to remove the distributor to gain better access to the oil pressure sensor.
In the back end of the transmission.
Inside the distributor.
There is no adjustment to my knowledge.
After the catalytic converter.
It is built into the alternator.
Remove the tail gate then replace water temperature sensor.
If it has a 4.3L engine the temp sensor is located next to the thermostat housing.
That would be the O2 sensor after the catalytic converter.
It has 1 coolant sensor, 1 temperature sensor
what is the wiring diagram for the o2 sensor on 2000 s10 blazer. it has 4 wires. what what do they all do /
The 2001 Chevy S10 4.3L engine takes 4 and 1/2 quarts with filter change.
From the 1985-1990 model year the 2.5 liter Iron Duke 4 Cylinder was used in the Astro as the base model. These were the same engines used from 1985-1993 in the Chevy S10.
fix vapor lock on 1998 chevy s10 2.2 liter 4 cylinder
which fuse is for the fuel pump in a 1993 chevy s10 blazer
on the distributor @ 2 oclock
4.3L? Inside the distributor.
2.2l is behind cat converter
We will need to know which engine it has to answer that.
2.2 Liter 4 cylinder, 2.8 Liter V6, 4.3 Liter V6 are factory engines. You can even install a Chevy 350 V8 with the proper conversion kit.
That should be the O2 sensor just before the catalytic converter.
Didn't have an air temp sensor in 92. Came out in 93.
You won't find one. The 1991 Chevy S10 doesn't have a MAF sensor.
Need to know gallons of what.
No it does not. That is a Ford thing.
An S10 is the same as a Chevy S10.