The cam sensor is inside the distributor.
The camshaft position sensor is located just above the oil filter on the right side (sitting in the vehicle) of the engine.
it is what keeps ur cranks shaft timed and in the right position
The cam sensor is inside the distributor.
I would like to know where the cam sensor is on a 1999 pathfinder and is there one or they calling it a crank shaft sensor The cam shaft position sensor is located in the distributor.
the crank shaft position sensor should be behind A/C compressor.
The throttle position sensor is located on the throttle body at the end of the throttle shaft.
where is the crank position sensor located on 2003 kia Rio 1.8
The crankshaft position sensor is located on the top of the transmission. It is located close to the bell housing.
The sensor is located directly above the crankshaft pulley. The camshaft sensor also connects with the crankshaft position sensor.
The crank shaft position sensor is located behind the harmonic balancer/crank shaft pully on the front of the engine. You can see the wires for the sensor run behinf the pully into a plastic housing.
The crank position sensor is located by the crank shaft on a ford 350 xl 5.8 liter.
2010 chevy malibu intake position sensor
where is the crank shaft pistion sensor located on a 2002 Chevy Malibu, and how hard is it to replace
The throttle position sensor is mounted to the throttle body on the end of the throttle shaft opposite of the lever.
That sensor is located on the cylinder head, right next to where the ignition coils are bolted to the engine.
The cam sensor is in the distributor.
The camshaft position sensor is on the driver side end of the cylinder head.
I don't believe that the altima had a crankshaft position sensor until 1995.
IT SHOULD BE LOCATED UNDER THE MANIFOLD BOLTED TO THE BLOCK
The crank sensor is located on the top of the bell housing on the drivers side.
crank or cam shaft position sensor is sometime the issue.it will not fuel if it cannot find the position of the cam or crank
Where is the crank shaft sensor located in a Audi a6
On the Daewoo Leganza it is located behind the AC compressor.
If it has a 4.3 V-6 it is in the disturber.
Front driver side corner of engine.
front right of cylinder head
a 1993 doesn't have a cam sensor. the crankshaft position sensor is located on the front of the engine directly above the crankshaft pulley
The 1999 Chevrolet Alamo crank shaft position sensor is located on the back of the engine. You will need to remove the rear engine cover in order to access the crank position sensor.
The TPS sensor is mounted on the throttle shaft on the opposite end of where the cable attaches.
on the top of the trans. bell housing right hand side
CMP= Cam Shaft Position Sensor.
The crankshaft position sensor is located on the rear of the engine. It is mounted just above the oil pan on the engine block.
It is behind and underneath the cam shaft gear.
A 1986 ford van does not a crank shaft position sensor,, it uses the pickup in the distributer
It is called a Throttle Position Sensor (TPS), and is located on the throttle body butterfly cross shaft opposite the throttle cable cam.
It is located in the front of the engine on the cylinder head. It's located on the passenger side of the vehicle.
Rear of engine between engine and trans but bolted to engineon the top side nest to firewall
Passenger side of the block, the gray item on the tall shaft near the oil filter.
The physical position of the sensor is behind the water pump pulley, where you can see the the cable connection on the cover of the crankshaft and camshaft gears.
It is located on the rightside of the intake manifold, infront the intake air tubing, sensor is in a vertical position, straight down in to the manifold.
I think you mean CAMSHAFT position sensor.
behind the crank shaft pully and the timing cover and then another pully is there two bolt hold it on
Replace the crank shaft position sensor- located on the top right hand side of the bell housing. Very difficult to replace but it will do all you have described
Cam shaft position sensor is on a rear of cylinder head -- you will see one of two cams protruding farther to the back than the other. The "blob" on its end is the cam shaft position sensor. Tightening torque for mounting bolts: 19 - 25 lb-in (1.9 - 2.6 N·m)
Follow the front wire on the distributor and it will lead to the crank shaft position sensor. hope this helps..
the cam shaft position sensor is located in the front of the motor on a 5.0 it is in the place of where the distributor was on older models it should be about center in the front
Mounted atop the transmission tail shaft.
The turbine shaft speed (TSS) sensor is located inside the automatic transmission.