On the 4.0L SOHC engine (VIN E), the Camshaft Position (CMP) sensor is a variable reluctance sensor, which is triggered by the high-point mark on the left-hand camshaft. It is mounted to the valve cover. The 4.0L and 5.0L engines use a separate CMP sensor mounted to the oil pump drive. The drive assembly is located toward the rear of the engine on the 4.0L, and towards the front on the 5.0L engine. 4.0L SOHC Engine (VIN E) Disconnect the negative battery cable. Disconnect the engine control sensor wiring from the camshaft position sensor. Remove the sensor retaining screw and the sensor from the left-hand valve cover. To install: Make sure the camshaft position sensor mounting surface is clean and the O-ring is positioned correctly. Position the sensor, then install the retaining screw and tighten it to 71-106 inch lbs. (8-12 Nm). WARNING Do not overtighten the screw; you may damage the sensor if the retaining screw is overtightened Engage the wiring harness connector to the CMP sensor. Connect the negative battery cable.
From the front of the vehicle the sensor is left of the harmonic balancer and above it.
where are the camshaft position
On the Ford 4.0 liter EFI , V6 engine : From what I have read : The camshaft position sensor is on the top of the engine , near the centerline , at the rear of the engine near the firewall . You cannot see it unless the upper intake manifold is removed
Where is the camshaft position sensor located on 1990 Lexus ls400?
Where is a camshaft position senser located on a 2006 dodge durango/
The camshaft position sensor is located on the end of the camshaft housing, on a 2002 Daewoo. The sensor should be labeled as such.
The Camshaft Position Sensor is located behind the Power Steering Pump.
where is the camshaft position sensor located on a 1999 Oldsmobile intrigue
The camshaft position sensor is located in the engine compartment of the 2002 Daewoo Leganza. It is at the end of the camshaft housing.
Do you have a video of the hhr camshaft position sensor
Where is the camshaft position sensor located on a 2003 Nissan Sentra GXE?
according to my Haynes repair manual the camshaft position sensor for the 4.0 L OHV engine is located at the rear of the engine block, on the top of the engine block
The Camshaft sensor is located in the distributor.
The 1997 Chevrolet K 3500 pickup truck camshaft position sensor is located on the back of the cylinder head. The camshaft position sensor should be labeled as such.
The camshaft position sensor is most likely located on the cylinder head of the engine. The location could vary depending on the manufacturer.
Where is the camshaft position sensor located on a 98 Mercury Mystique 2.4??
The camshaft position sensor on your 2002 automobile is located on the front of the camshaft. You will need to remove the front engine cover to access the sensor.
The camshaft position sensor on a 4.3L engine would be in the distributor.
In a 1996 Ford Explorer , 4.0 liter EFI , V6 engine : From what I have read the camshaft position sensor is located on the top of the engine , near the centerline , at the rear of the engine near the firewall . Apparently you can't see it until the upper intake manifold is removed
The 2002 Ford Ranger camshaft position sensor is located on the back of the camshaft. The rear engine plate will need to be removed in order to view the sensor.
The camshaft position sensor on a 2002 Mitsubishi Gallant is located behind the rear camshaft bearing. It constantly updates the vehicle' computer about the status of the camshaft.
Located on the top front left (drivers side) valve cover. Vehicle production date is 04/03
where is bank 2 camshaft located audi a6 2.8 1999
the cam shaft position sensor is located in the front of the motor on a 5.0 it is in the place of where the distributor was on older models it should be about center in the front
For the Satur S-Series there is no camshaft position sensor. They never installed it in that model