answersLogoWhite

0


Best Answer

If its a new Liberty just call the Dealer or any Dodge/Chrysler Dealer for the location. On the 2002 Liberty it is in the right rear corner. You remove the plastic covering and there is the connector there where you can connect in an adapter. There is also a rubber plug in the right rear corner intended to allow you to feed the wire out without drilling a hole. You then reseal the rubber grommet with silicone sealant.

User Avatar

Wiki User

โˆ™ 2006-02-09 18:06:39
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the connection for the taillight wiring to connect a trailer wiring harness in a Jeep Liberty?
Write your answer...
Submit
Sign up for more answers

Registered users can ask questions, leave comments, and earn points for submitting new answers.

Already have an account? Log in

Related questions

Where is the connection for the taillight wiring to connect a trailer wiring harness in a 2003 Jeep Liberty Sport?

It is the round connector, with a cover over it, about 6 inches left of and about at the same level as the hitch receiver.


Where is the brake light wiring harness for 1989 Chrysler Lebaron?

It plugs into the taillight.


What color is the backup light wire in a 2003 Passat taillight harness?

i dnt no i dnt no


What does the pink wire in the wiring harness connect too?

the harness


How do I Replace tail light 2006 mustang?

Taillight bulb replacment/Taillight housing replacement * Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you replace a taillight bulb on a 2006 ford mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you change a taillight bulb in 2006 Mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


What could cause no spark no fuel but it will crank over and when you fudge with wires the fuse box will click and then it will start but then kill over a little after i know the crank but its good?

If shaking the wire harness allows it to run for a little while, you have a connection issue in the harness.If shaking the wire harness allows it to run for a little while, you have a connection issue in the harness.


How do you disconnect taillight wires 2002 silverado?

remove the 2 bolts/screws attaching the lens to the bed, after that unplug the harness and your done


How do you change tail light bulbs on 2006 Mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you replace a tail light bulb on a 2005 mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you change the tail lights on a 2007 mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you replace the tail light bulbs in a 2006 mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you change a tail light on a 2006 mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How and where do you connect the turn and taillight wires for a trailer lighting connector on a Lexus ES-300?

It sounds as if you either don't have a wiring harness attached to your vehicle, or else you will need to get an adapter. All the plugs and sockets are different, depending on who made it, and how many connectors each one has.


Bundles of wires that connect computer parts?

Harness. Cables.


How do you install speakers into a 94 Honda Accord that has a srock wiring harness?

You can buy a speaker harness. An adapter that connect the positive and negative from the speaker into the stock harness.


What is the cause of a rapidly flashing taillight on a trailer attached to a vehicle?

You have a live wire shorting out in the signal circuit. Check the wire harness for damage.


How do you change the tail light bulb on a 2006 Ford Mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you get to the tail light in a 2006 V6 Mustang to change the bulb?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you change the rear tail light bulb on 2006 Mustang?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you change the bulb for the tag light on a 2005 mustang gt?

* Remove the rear inside trunk finishing panel to access the taillight housing mounting nuts * Free the grommet for the taillight electrical harness and the three taillight housing nuts then pull off the taillight housing * Rotate the bulb socket counterclockwise and pull it out of the taillight housing * To remove the bulb from the socket pull it straight out.To install a new bulb in the socket push it straight into the socket until it stops


How do you change the taillight on a 1987 Chevy Corvette?

If all you want to do is change a bulb, you pull the license plate off to gain access to the wiring harness. After you twist the harness counter clockwise to loosen the harness, let it drop down and access it to change the bulb from underneath the car.


Do you need any new wiring to swap 1994 Mustang taillights with those from a 1998?

no, however one of the bulbs on each side wont fit properly. To do it right you should use the taillight harness from a 96-98 car. no, however one of the bulbs on each side wont fit properly. To do it right you should use the taillight harness from a 96-98 car.


What does the harness connector of an alternator connect to on both ends?

plus and ground