Where is the crank sensor located in a 2002 Chrysler Sebring LX?

where is the crank sensor located on my 1997 Chrysler sebring lxi

Replace the crank sensor located on bell housing of trans.

It is on the top rear of the transmission bell housing.

It is on the top rear of the transmission bell housing.

Possibly the crank sensor or the coil pack is dead. But with a dead crank sensor you also get no spark, no crank. No crank equals no fuel delivery.

1391 is for an intermittent loss of the cam sensor or crank sensor signal

It is on the top rear of the transmission bell housing.

There is a tone wheel on the crank/flywheel that the sensor reads off of, if that is your question.

The crank sensor is located under the car near the exhuast. If you have the replacement you'll see it easy.

The most common would be engine cranks but does not start.

Since the Sebring has spark and compression , check the crank sensor, and the timing belt. If the timing has jumped or the sensor is bad then the engine will not start.

It is on the top rear of the transmission bell housing.

It is located directly below the distributor. It is on the transmission bellhousing on the firewall side. It is hard to see without some stuff moved out of the way.

It is on the top rear of the transmission bell housing.

Out of gas, fuel pump, cam sensor, crank sensor, coil, computer, alternator, etc.

Many other options. No fuel pressure, broken timing belt, computer malfunction, no spark,

Yes, it could along with dozens of other possibilities.

A) On a 2.0L & 2.5L DOHC (1999 & earlier) Engines, The crank shaft sensor is mounted above the oil filter. B) On 2.4L DOHC ( 2001 & later) engines, the crankshaft sensor is mounted on the rear side of the engine block C) On 2.5L V6 engines, the crank shaft is mounted under the distributor near the transaxle housing.

Check the crank angle position sensor. It is located on the left side (drivers), at the crank shaft. There is one fastener and an electrical plug to remove the sensor. I found it was easier to get off and back on by removing left front wheel and going through the wheel well.

It has one. It is located on the top rear of the transmission bell housing.

The sensor is under the car on the back of the engine on the left side on the 2.4L. On the 2.5L it is on the top rear of the transmission bell housing.

Passneger side of the bell housing.

It is on the top rear of the transmission bell housing. It is on the top rear of the transmission bell housing.

If you don't have fire at the plug, change the crank sensor first, then the coil.

How do you replace crank shaft sensor on 2005 Chrysler 2005 300c?

There is no way for us to know that.

No crank sensor, only a cam position sensor.

where is the crank positioning sensor on a 1996 newyorker van

It could be either the crank angle sensor or the distributor module. If it is the distributor module, you have to buy and install a re-man distributor.

It's in the top of bell housing of the transmission near the back of the engine compartment.

Just behind the engine, in the passenger side of the bell housing.

the crank sensor is located in the transmission bellhousing on the lower passenger side where the trans bolts to the engine almost right above the right axle shaft. one 10 mm bolt holds the sensor in place, this is on the 3.5 liter engine,

crank shaft sensor is near the oil filter. I have the repair manual but I am unable to past the page in here.

the crank sensor is located just behind the crank shaft pully of the engine.

top rear of bellhousing... it has a exciter ring made on the flywheel

Where is the crank shaft sensor located in a Audi a6

That year did not have a crank sensor.

If the head of the key is gray, then yes.

No you do not.

the crank sensor is located on the top front of the tranny

The dealer sells a cardboard spacer the glues to the tip of the crank sensor. You then install the sensor and push it tight to the flex plate.

where is the crank sensor located on a 2002 Oldsmobile intrigue 3.5

where is the crank position sensor located on a 2004 hyundai v-6 2.7 engine

Chrysler does not use reset switches. Chrysler does not use reset switches.

It does not have a crank case sensor. It does not have a crank case sensor.

The 1995 Oldsmobile Aurora 4.0 liter engine crank sensor is located on the back of the crank. You will need to remove the rear engine cover in order to view the crank sensor.

where is the crank sensor located on 2000 nissan sentra

where is the crank sensor located on a 2005 chevy impala

The Crank position sensor is located on the right side behind the wheel about midway up the motor eaiseier to get to from the bottom with 10mm socket one bolt

The crank position sensor is located by the crank shaft on a ford 350 xl 5.8 liter.