Quantcast
answersLogoWhite
notificationBell
Oldsmobile Cutlass Supreme
Ford Crown Victoria
Crankshaft Sensors

Where is the crankshaft sensor located on a '96 Crown Vic?


Top Answer
User Avatar
Wiki User
Answered 2010-09-02 06:42:06

on passenger front of the engine block between the a/c compressor and front cover.you will have to move the compressor out of the way to get the sensor out.

Answer :

Do not bother unbolting the compressor, just unplug any wires that are in the way, including the Crank. pos. sensor. Does the car crank but no start, I ask because that is usually the sympton of the crankshaft pos. sensor. Long extensions will help get to the bolts, swivels or wobble extensions if needed.

123
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

Cam sensor ford crown Victoria?

where is the cam sensor located on a 2003 ford crown vic


How do you change a crankshaft sensor on a 1993 crown vic v8?

The crank shaft sensor is located on the bottom portion of the timing cover to the left of the crank pulley. Look for two wire harnesses and remove them along with the bolt.


Where is the camsensor located on a 96 crown vic?

it is underneath your alternator,it must have a black wire to the sensor


Where is the cooling Fan temperature sensor on a crown vic?

coolant fan temp sensor 1998 crown victoria



Where is the speed sensor on a 1991 crown vic?

oN THE 91 FORD CROWN VICTORIA YOU WILL LOCATE THE SPEED SENSOR ON THE DRIVERS SIDE OF THE TRANSMISSION ON THE TAIL SHAFT.


95 crown vic Where is the camshaft position sensor?

The 1995 for Crown Victoria camshaft position sensor can be found on the back of the cylinder head. The camshaft position sensor will be labeled as such.


Where is FLAPPER located for ac in 2006 crown vic?

how do you get to the flapper for ford crown Victoria


Where is the Crown vic radio antenna located?

Your Antenna is located on the back window of the car


Where is a o2 sensor located at on a 1993 ford crown vic v8?

They are located on the exaust system, screwed directly into the exaust pipes, one on each side of the engine, right after the exaust manifolds.


2000 crown vic the motor has locked up the crankshaft will not turn help?

A little more info, I am unable to understand your question!


Where is the ignition control module on a 1992 Crown Vic?

Where is the ignition control module located in my 1992 Crown Victoria


How does your fuel gauge work on your 89 crown vic ltd?

signal from the sensor inside the tank to the gauge


Where is the headlight relay located on a 94 crown vic?

It is located behind the dash to the left of the radio/heater controls.


Is there a difference in a plain 97 crown vic transmission from a 97 crown vic police intercepter?

the 97 crown vic transmission is for the car and the interceptor is police car


Where is the fuel pump on a 2000 crown vic?

How to change. Fuel pump on 200 crown vic


Where is the thermostat located on a 1989 ford crown vic?

The thermostat housing is located at the front of the engine just beneath the distributor.


Why my temperature gauge don't work on my 1992 crown vic?

Most likely a faulty sensor, or the gauge itself is bad


Where is the dome light door switch located on a 1999 p71 Crown Victoria?

on my 98 crown vic you have to push in the head light switch


Will a 1997 crown vic motor go in a 1993?

A 1997 Crown Vic motor will fit a 1993 Crown Vic, both cars came with the exact same engine from the factory.



Where is the fuel filter on 85 crown Victoria ltd?

On my 1988 Crown Vic, The fuel filter was located on the passenger side, right in front of the rear tire, tucked up on the frame but the models of the '85 and '88 crown vic are different. but i hope this helps you.


Where is the fuse box located on a 1988 ford crown vic?

WHERE IS THE FUSE BOX LOCATED ON A 1988 FORD CROWN VICTORIA


Fuse diagram 95 crown vic?

The fuse diagram on a 95 Ford Crown Vic is located on the cover of the fuse panel and within the repair manual. It makes the process of locating each fuse much easier.


What does the code P1131 on a 2002 crown vic?

Trouble code P1131 means: Lack Of HO2S11 Switches - Sensor Indicates Lean


Still have questions?

Trending Questions
How to Make Money Online? Asked By Wiki User
Best foods for weight loss? Asked By Wiki User
Previously Viewed
Unanswered Questions
How old is zak beggans? Asked By Wiki User
Does arsenio hall have ms? Asked By Wiki User