Where is the crankshaft sensor on a 2004 durango with a 4.7 magnum engine?

Dodge did not produce the Durango until 1998. It is located on the bell housing on the right side of the engine where the transmission mounts to the engine

The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine It is positioned and bolted into a machined hole in the engine block

Behind the engine, in the passenger side of the transmission bell housing.

If the crankshaft sensor is dead the engine will not start

Normally if the crank sensor fails while running,the engine can keep running with just a working camshaft sensor.

The 1998 Montero Sport crankshaft sensor will be located on the rear of the engine. The crankshaft sensor is on the inside of the rear engine cover.

is the crankshaft position sensor the same and the engine speed sensor

The location of the crankshaft position sensor depends on which engine the car has. If it is the 2.5L 4 cylinder engine the crankshaft position sensor is behind the ignition module. If it is the 2.8L V6 engine the crankshaft position sensor is on the side of the engine nearest the firewall and just above the pan rail in about the center of the block.

The 1995 Mitsubishi Eclipse crankshaft position sensor is located on the back of the engine. The crankshaft position sensor will be near the bottom of the engine cover.

No, the 1983 model does not have a crankshaft position sensor. Only distributorless engine needs a crankshaft position sensor.

Try checking for the crankshaft sensor

The 2001 Chevy Express Van crankshaft sensor will be on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft sensor.

The 2004 Chevy Malibu crankshaft position sensor location is dependent upon the type of engine. In most cases the crankshaft position sensor is on the back of the engine.

The crankshaft sensor for this model is located at the front of the engine, near the crankshaft itself.

Where is located the crankshaft sensor in Chevy avalanche 2002 engine 5.3?

where is the crankshaft sensor on a 1994 dodge pickup with a 5.9l engine?

the 92 4afe toyota engine does not have a crankshaft position sensor

The rear crankshaft sensor is located on the back of the crankshaft. The rear engine cover will need to be removed in order for the sensor to be visible.

The crankshaft position sensor measures the rotational position of the crankshaft for the engine computer. That info is required for fuel and ignition timing.

The 1994 Ford F1 50 crankshaft sensor is located on the back of the engine. You will need to remove the rear engine cover in order to access the crankshaft sensor.

The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.

The crankshaft position sensor is located on the front of the engine. It is just to the left of the crankshaft pulley.

An intermittent crankshaft sensor will not let the engine fire the correct times. This can definitely cause a misfire for the engine.

crankshaft sensor is on the right rear corner drivers side of the engine.

The crankshaft sensor is located in the engine on a Chevy 1500 truck. This is under the hood.

The 2001 BMW 325 crankshaft position sensor can be found on the back of the engine. The position sensor will be near the bottom of the rear engine cover.

A crankshaft sensor senses the engine revolutions to basically tells the the car when 2 inject and ignite the fuel

changing the crankshaft sensor

It's located behind the crankshaft pulley bolted to the engine block.

The crankshaft sensor is mounted to either side of the front side or the back side of the engine depending on the engine type

The crankshaft position sensor bolt size isÊdependent upon the type of engine. In most cases the crankshaft position sensor 9/16.

The crankshaft sensor in your 1990 former Roche is located on the front of the engine. The best way to test your crankshaft sensor is to hook the engine to a Dyno tester.

on the engine

The REF crankshaft position sensor is mounted at the front of the engine on the aluminum oil pan section below the crankshaft pulley The POS crankshaft position sensor is mounted on the aluminum oil pan section at the rear of the engine near the transaxle bellhousing

Crankshaft position sensor function is to monitor the position or rotational speed of the crankshaft. It is an electronic device and it is used in the internal combustion engine.

crankshaft sensor is located just behind the crankshaft pulley on the front of the engine(passenger side of vehicle).

The crankshaft position sensor can be found on the bottom of the engine in a 2000 Honda Civic EX. It is next to the crankshaft itself.

The Ford falcon crankshaft sensor is located on the back of the crankshaft. The sensor can be seen when the rear engine cover is removed.

The crankshaft position sensor is located on the lower engine block beneath the exhaust manifold on the firewall side of the engine.

The crankshaft sensor is located on the lower part of the engine closest to the firewall, on the passenger side of the car.

No it does not have a crankshaft sensor, the engine control module uses the distributor for crankshaft position.

A bad crankshaft sensor can have several symptoms. The engine could stall, backfire, be sluggish or not run at all.

i have replace the crankshaft sensor but the code cannot be erased

On front cover of engine by crankshaft pulley.

Back side of the engine near where the transmission mounts to the engine. You have to jack up the car and crawl under it to see it. There are two sensors there.....the crankshaft sensor and the knock sensor.

A crankshaft sensor, on a Hyundai XG350, can be installed by simply plugging the new sensor into the slot of the old sensor. The sensor can be located on the back of the engine cover.

Begin by removing the rear engine cover from your 1997 Land Rover Discovery. Remove the crankshaft sensor wiring harness. Remove the crankshaft sensor retaining bolts. Reverse the process to install your new crankshaft sensor.

On the 2.8 V6 engine the crankshaft position sensor is near the bottom center of the block on the side nearest the firewall. On the 2.5L 4 cylinder engine the crankshaft position sensor is behind the ignition module below the intake manifold.

The crankshaft sensor on a 2001 Chevy Silverado 8100 is located on the bottom of the engine, near the starter. It constantly monitors where the crankshaft is in its rotation.

The 1997 Nissan pickup truck crankshaft position eight sensor can be found on the back of the engine. The positioning sensor will be halfway down the engine block.