0
Don't know the vehicle in detail but the sensor can only be either round or next to the front crankshaft pulley or on round the flywheel, perhaps on the bell housing? the crankshaft sensor for a Jeep 2000 is located behind the starter you have to remove the starter to replace it Tommy :-)
Wiki User
∙ 18y ago
Wiki User
∙ 9y agoA 5.2 crank sensor is located on the rear of the cylinder head on the passenger side. It is at where the block&head bolt together. You will need a (I believe) a 7mm hex head. Use 1/4 drive with extensions and several swivel joints. remove spark plug wiresto ease access.
Once you see it, you'll understand.
I think that might be the Camchaft positioning sensor, a very common mistake. I've even heard of people taking their jeep in to get the crank sensor replaced and the mechanic replaces the cam sensor instead. I believe the crank sensor (on the 1993 jeep grand Cherokee limited anyway) with the 5.2l v8 is located on the passenger side of the vehicle mounted on the bellhousing. I'm actually getting ready to replace mine right now.
Both answers are correct for the crank (crankshaft) sensor. The camshaft sensor is located on a plate in the distributor.
Wiki User
∙ 16y agoon the 4.0 6 cyl engine the crank position sensor is mounted to the bell housing drivers side top. so if you look from drivers side fender it will be just behind the engine where the transmission bell housing bolts to the rear of the engine.towards the top.
Wiki User
∙ 13y agoFor a (U.S.) 6 cylinder, it is on the drivers side near the top of the bell housing. For 5.2 and 5.9 V8s, it is on the passenger side at about a 1 o'clock position (behind engine) where the head meets the block.
Wiki User
∙ 14y agoI could answer your question, and the others on here by telling you exactly where to locate the item you're looking for on your vehicle. But, I'm not. I believe in teaching someone to fish soo... go down to your local auto-parts store and buy the Haynes or Chilton book for your vehicle. Runs between 15 and 25 bucks and next to buying a OBD code reader, it's the most well spent money you'll ever spend on your vehicle.
The repair book not only tells you how to fix stuff on your vehicle, it also tells you WHERE stuff is... for the most part. And tells you how much fluid to add, and whether your mechanic is going to rip you off. Like my Jeep, it's fuel filter is life of vehicle and is therefor located IN the gas tank, but that doesn't stop Lube places from telling me I should change it. The book though, tells me to tell them to hit the road....
Wiki User
∙ 14y agoI'm not sure if it's the same on the 2004 but I have a 1989 and it's on the top left side of the transmission bell housing.
Wiki User
∙ 13y agoLocated on the driver side where the trans and engine meet right beside the exhaust pipe.
Wiki User
∙ 13y agoon the top of the trans. bell housing right hand side
Add your answer:
Earn +20 pts
Where is the maf sensor located on a 2004 Jeep Grand Cherokee?
It does not have a mass airflow sensor.
What is the life of oil sensor switch on 2004 Jeep Grand Cherokee?
There is no such sensor, the oil change reminder only runs off of mileage on a 2004
How many valves does the 2004 Jeep Grand-Cherokee have?
The 2004 Jeep Grand-Cherokee has 12 valves.
What is the maximum payload of the 2004 Jeep Grand-Cherokee?
The maximum payload of the 2004 Jeep Grand-Cherokee is 1100 lbs..
What is the turning circle of the 2004 Jeep Grand-Cherokee?
The 2004 Jeep Grand-Cherokee's turning circle is 37.4 ft..
Where is the crank shaft position sensor 2004 silverado?
It is behind the starter.
Location of crank shaft position sensor of a Nissan Altima 2.5 04?
Location of crank shaft position sensor of a Nissan altima 2.5 2004? send diagram please
Where is the crank sensor located on a 2004 Oldsmobile alero 4 cylinder?
The crank shaft position sensor is just above the oil filter at the tail end of the starter
Where is crank shaft sensor located on 2004 Tahoe?
It is bolted in the side of the block BEHIND the starter. You will have to REMOVE the starter.
Where is a crank shaft sensor located on f350 6.0 2004?
bottom front on passanger side behind a/c compressor.
Where is the crank shaft sensor on a 2004 4.3 v6 truck?
It is on the bottom left side of the timing cover, behind the balancer.
Why does my Mitsubishi L200 go into limp modewhen crank sensor has been replaced?
hi i have a 2004 mitsubishi l200 ediesel that wont start,turns over but not firing,been told its the crank shaft position sensor
Where is the crank shaft sensor located on a 2004 Dodge Stratus 2.4L DOHC?
Back of the block, about two inches above oil pan.
Where is the crank shaft sensor on 2004 Hynudai Sante Fe 2.4 engine?
It is under the timing belt cover near the crankshaft pully / harmonic balancer.
Where the crank position sensor is located?
where is the crank position sensor located on a 2004 hyundai v-6 2.7 engine
How do you replace a crank sensor on a 2004 jetta?
How_do_you_replace_a_crank_sensor_on_a_2004_jetta
Where is the crank sensor on 2004 sebring 2.4l?
The crank sensor is located under the car near the exhuast. If you have the replacement you'll see it easy.
