Crankcases and PCV Valves
Mazda MPV
Toyota Tundra
Grand Prix GT

Where is the exact location of the PCV valve on a 1991 Mazda MPV with the 3.0 V6?

202122

Top Answer
User Avatar
Wiki User
2009-02-04 19:39:26
2009-02-04 19:39:26

My 89 Mpv's is located right in the middle of the engine compartment underneath the intake.Its is an inline pcv so follow the hose up to it.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The safety fuel shut off location on a 1991 Mazda MX6 is under the dash. It is on the far right side in front of the passenger seat.

User Avatar

The EGR valve for a Honda EX 1991 is at the top of the engine. It is at the front, just to the left of center.

User Avatar

In between the bumper and the frame, on the passenger side.

User Avatar

Napaonline.com pick you vehicle on the left and browse the gasket section

User Avatar

The idle air control valve is located next to the throttle body. It is connected to the air cleaner hose on the top of the engine.

User Avatar

It is inside the transmission, on the rear corner of the valve body.

User Avatar

how do remove the brake drum on a 1991 mazda 323

User Avatar

The air control valve on a 1991 4.3 S10 is on the engine. Kindly refer to your usual manual to see the exact point, where it is located. The Idle Air Control is attached to the base of the throttle body.

User Avatar

Mazda Navajo was created in 1991.

User Avatar

Most 1991 sending units on a 1991 Le Sabre screw in. The exact location for the sending unit will depend on which one needs changing.

User Avatar

it is on the throttle body. usually held in by two screws.

User Avatar

It is inside the transmission, on the rear corner of the valve body.It is inside the transmission, on the rear corner of the valve body.

User Avatar

Check your owners manual for the location of your daytime running light module. The manual should have a diagram with its exact location.

User Avatar

check over the back axle like directly obove attached to the wall driver side.

User Avatar

Can someone please tell me how to hot wire the ignition of a 1991 mazda protege?

User Avatar

The 1991 Geo Metro EGR valve can be located on the air cleaner housing. The valve will be on the back of the housing.

User Avatar

A standard 1991 Mazda 626 was originally equipped with 185/70-14 tires. A 1991 Mazda 626 Turbo came originally equipped with 195/60-15 tires.

User Avatar

Depending on which engine is in, I know that it's on top-right part of the engine on the 8V model.

User Avatar

It does not have one, You have to remove fuel pump relay to shut fuel off.

User Avatar

The PVC valve is located at the left side rear of the intake manifold under a flat metal plate cover held in place with three screws.

User Avatar

the PCV valve is located on the valve cover of a 1991 Regal Custom. It is plugged in and can be easily changed.

User Avatar

It is important to know as much as possible about the car that it is driven. Yes, there is a clutch adjustment on a 1991 Mazda 929.?รฆ

User Avatar

The PVC valve for a 1991 Skylark should be located on the top of the valve cover. It is a plug in type, twist and pull to remove.

User Avatar

4 cylinder does not have pcv valve.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.