With ignition off hold down up and down button of trip computer while holding down turn on the ignition for 3 seconds (beeps) release and press the mode button release the mode button press and hold the up and down buttons for 3 seconds (beeps) release buttons turn off ignition
how to replace a fuel line presure regulator on a 2004 4.8 chevy silverado
try this video with the instructions located below the videio http://www.ehow.com/video_4804005_replace-pressure-regulator-gm-engine.html
i had this issue, im not sure exactly why it does it, but i had to replace the trans.
in the gas tank attached to the fuel pump. Replace it with the pump.
faulty fuel pressure regulator , it should be located on or near the fuel rail. replace it. that should do it. actually, the fuel pressure regulator is located on top of the fuel sending unit in the gas tank. (unless its a 95 or early 96 with the steel tank)
It is located under the intake manifold, if you do not have external fuel injectors. Anybody have a picture of the location? Any special instructions to replace it?
u dont it does it by itself just put it in the area of fuel and boom a pressure regulator
Hi. It is located behind the TBI right where the two fuel lines go in. To replace it you have to remove the carb, and remove the top and lift the whole top off, under there you will see the regulator.
Fuel Pressure Regulator is located on the fuel rail.Fuel Pressure Regulator 1. Disconnect the negative battery cable. 2. Properly relieve the fuel system pressure. 3. Remove the air cleaner outlet tube(s). 4. Remove any necessary components to access the pressure regulator. 5. Disconnect the vacuum hose from the pressure regulator. 6. Remove the pressure regulator attaching screws. 7. Remove the pressure regulator from the fuel rail. To Install 8. Discard the O-rings on the pressure regulator and replace them with new ones. 9. Lubricate the O-rings with clean engine oil. 10. Install the regulator into the fuel rail and tighten the retaining screws. 11. Connect the vacuum hose to the regulator. 12. Install any components removed to access the regulator. 13. Install the air cleaner outlet tube(s). 14. Connect the negative battery cable.
Fuel Pressure Regulator is located on the fuel rail.Fuel Pressure Regulator 1. Disconnect the negative battery cable. 2. Properly relieve the fuel system pressure. 3. Remove the air cleaner outlet tube(s). 4. Remove any necessary components to access the pressure regulator. 5. Disconnect the vacuum hose from the pressure regulator. 6. Remove the pressure regulator attaching screws. 7. Remove the pressure regulator from the fuel rail. To Install 8. Discard the O-rings on the pressure regulator and replace them with new ones. 9. Lubricate the O-rings with clean engine oil. 10. Install the regulator into the fuel rail and tighten the retaining screws. 11. Connect the vacuum hose to the regulator. 12. Install any components removed to access the regulator. 13. Install the air cleaner outlet tube(s). 14. Connect the negative battery cable.
We need to know what year and engine you have to accurately answer that Q.Fuel Pressure Regulator is located on the fuel rail.Fuel Pressure Regulator1. Disconnect the negative battery cable.2. Properly relieve the fuel system pressure.3. Remove the air cleaner outlet tube(s).4. Remove any necessary components to access the pressure regulator.5. Disconnect the vacuum hose from the pressure regulator.6. Remove the pressure regulator attaching screws.7. Remove the pressure regulator from the fuel rail.To Install8. Discard the O-rings on the pressure regulator and replace them with new ones.9. Lubricate the O-rings with clean engine oil.10. Install the regulator into the fuel rail and tighten the retaining screws.11. Connect the vacuum hose to the regulator.12. Install any components removed to access the regulator.13. Install the air cleaner outlet tube(s).14. Connect the negative battery cable.
Fuel Pressure Regulator is located on the fuel rail.Fuel Pressure Regulator1. Disconnect the negative battery cable.2. Properly relieve the fuel system pressure.3. Remove the air cleaner outlet tube(s).4. Remove any necessary components to access the pressure regulator.5. Disconnect the vacuum hose from the pressure regulator.6. Remove the pressure regulator attaching screws.7. Remove the pressure regulator from the fuel rail.To Install8. Discard the O-rings on the pressure regulator and replace them with new ones.9. Lubricate the O-rings with clean engine oil.10. Install the regulator into the fuel rail and tighten the retaining screws.11. Connect the vacuum hose to the regulator.12. Install any components removed to access the regulator.13. Install the air cleaner outlet tube(s).14. Connect the negative battery cable.