answersLogoWhite

0


Best Answer

the fuse panel on my 98 is on the left end of the dash. open the door to see it. my brake lights stopped working but did not blow the fuse. had to change the brake switch located on the brake pedal. good luck

User Avatar

Wiki User

โˆ™ 2005-12-12 15:33:10
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the fuse block for the brakes on your 1993 ford ranger brake lights do not work?
Write your answer...
Submit
Related questions

Why does ford ranger brake warning lights remain on?

if you have your parking brake off and it is still on, then you have a problem with your brakes somewhere, you need to check the fluid, lines, pads and all the other stuff


What do I do if the brake light came on in my 2002 Ford Ranger brake is not on but the brakes seem suddenly super squishy?

You probably need to change your back brakes.


Bleeder valve for a 1997 Ford Ranger where is the bleeder valve for a 1997 Ford Ranger located?

The bleeder valve for the brakes on a 1997 Ford Ranger is located in the brake line where it meets the brake disc. The wheel will have to be removed to access the bleeder screw for drum brakes.


Your brake lights dont light up when you pushe the brakes but the blinkers and everything else works on the tailights what is the problem?

Check the 30 amp brake fuse (green) in the engine compartment fuse block.


Why would the tail lights work on a 1990 Camry but the brakes lights will not even after you replaced the bulbs and the fuse to the brakes?

Check the switch at the brake pedal .


Your brake lights and head lights do not work your blinkers and running lights do?

My rear window brake light works, but not my tail light brakes on my 1997 Monte Carlo. What is the problem?


Why does the emergency brakes lights come on when driving and the brake is not engaged?

it may need some brake fluid


Brake light switch sticks?

brake lights say lit after ignition has been shut off. lights shut off after hitting the brakes.


What is the minimum brake rotor thickness for a 2003 Ford Ranger?

It is important to maintain your brakes properly. The minimum brake rotor thickness for a 2003 Ford Ranger is 0.99 inches.


Where is the Brake light switch Nissan pintara 1988?

There is no switch to activate or deactivate the brake lights on a 1988 Nissan. The brake lights automatically turn on any time the brakes are pressed.


Brakes lights don't work on Toyota Tacoma?

every vehicle must have brake lights to indicate that the vehicle is stopping. with no brake lights the vehicle can cause a rear end collision.


1990 ford ranger brake lights won't work?

check brake light fuse and brake light switch on pedal


What is wrong when no brake lights and all other lights work 2004 dodge stratus?

I tried all the fuses, the parts that under the brakes I checked that. All lights come on and working except the brake lights no break lights.


Why do Turn signal works but not brake lights your jeep?

Check the fuses for your brakes.


Does the flasher relay have anything to do with your brake lights?

No, if your brakes are flashingyou have crossed circuits.


What would make the brake lights short out in your 2001 ford ranger?

More than likely you are having Electrical issues with your 2001 Ford Ranger brake lights. Contact your local service dealer for further information.


What is wrong when your brake light on the dash lights up and you have no brakes but when you repress the brakes the light goes off and your brakes are back?

check fluid level


Why do the blinker lights and brake lights work but tail lights don't work on 1987 ford ranger?

The tail lights are on a separate wiring than the blinker/brake lights. Look for a blown fuse or a broken/loose wire.


What do you do if your tail lights do not work while driving though brake lights work fuses and bulbs are good?

on some cars the tail lights and brake lights are totally different bulbs gain access to the bulbs and have someone push the brakes so that you can determine which bulbs are the brake lights and replace the tail lights


Why would the brake lights stay on whenever the car is on even after you have replaced the brake light switch?

Out of adjustment. Adjust the mounting of the switch so the brakes lights are off until you press the brake pedal.


Why do a 93 Chevy caprice brake lights don't work when you hit the brakes?

In the 1993 Chevy Caprice there is a brake sender located inside the steering column where the brake pedal is attached. Perhaps the brake lights are not working because of this, when a person hits the brakes. There could also be a fuse blown or a broken or shorted wire.


Can a bad bulb cause all brake lights in a 98 ford ranger to fail?

It can if it is a dual filament bulb as found on most US. makes. The brake light filament can short over to the tail light filament inside the bulb and when the brakes light is activated, all the tail lights and front marker lights will light also, probably blowing fuses.


Why is it hard to press down your brake pedal on a ford ranger?

more than likely you have air in brake line and need to bleed brakes


Which lights are the brake lights and which lights are the fog lights?

Fog lights are in the front; they are commonly referred to as "brights" because they are the brighter of the two standard headlights. Brake lights are in the rear; they light up when pressure is applied to the brakes or when the car is in park or reverse.


What fuse controls brake lights?

What fuse controls the brake lights on a 1998 Chevy Camaro? It should be labeled on the fuse block.

People also asked

Ford mondeo stereo fuse?

View results
Study guides

๐Ÿ““
Create a Study Guide