Best Answer

It may be located in the airbag sensor control unit.

User Avatar

Wiki User

โˆ™ 2006-09-21 22:00:22
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: Where is the gravity rollover sensor located on a Isuzu Rodeo?
Write your answer...

Related Questions

Where is the knock sensor in a Isuzu I290?

The knock sesor is located, on your Isuzu 1290, at the front of the engine. The sensor screws into the engine. Wires connect the sensor to the senor light.

Where is the coolant temperature sensor located on a 1998 Isuzu Amigo 2.2L engine?

The coolant temperature sensor is located under the hood of the car. The sensor is located to the left of the brake booster at the rear of the engine.Ê

Where is bank 1 sensor 2 on a 2000 Isuzu trooper located?

Driver side

Where is the fuel level sensor located on a 1999 Isuzu rode?

Inside the fuel tank.

Where is the MAF sensor located on a 1990 Isuzu Trooper 5 speed 2.8 liter v6?

The 1990 Isuzu 2.8 liter engine MAF sensor can be found on the firewall in the engine compartment. The sensor will be on the passenger side of the firewall.

Where is the O2 sensor in bank 2 located in your 1996 Isuzu trooper?

Bank 1 is the side that cylinder 1 is on, sensor 1 is downstream and sensor 2 is upstream

1998 Isuzu rodeo 3.2 engine knock sensor location?

The knock sensor is located on top of the engine block underneath the intake.

Where is the crank sensor located on a 2004 Isuzu axiom?

Isuzu part number 8-97258-523-0(MSRP $193.86) crank sensor is on the right side(passenger) of the engine block, just behind the mount.

Where is the o2 sensor located on a 1997 Isuzu rodeo?

the o2 sensors are located on the exhaust pipe one by trans and one by the muffler there is 2 of them

Where is a camshaft position sensor on a 2001 Isuzu rodeo?

It is located between the camshafts right behind the camshaft pulley's.

What does O2 sensor mean on Isuzu Rodeo?

oxygen sensor

Where is speed sensor located 2003 Isuzu Axiom?

Rear top of transmission case near drive shaft output.

What is the tps sensor on a 95 Isuzu Rodeo?

It is a Throttle Position Sensor

Where is the overdrive sensor on 1998 Isuzu NPR?

The sensor will be by the accelerator pedal

Is there a diagram of oxygen sensor location on an Isuzu trooper?

Yes, there is a diagram of the oxygen sensor location of a Isuzu Trooper. This diagram can be found in the cars maintenance manual.

Where is the g sensor located on a 1997 Isuzu rodeo 3.2l ecu codes p1390 p1391 p1392?

G sensor is right side of frame Could you be a little more specific please?

Where is the G Sensor on a 1996 Isuzu Trooper?

The g-sensor is located under the passenger side rear of vehicle in front of fuel tank just off of the frame rail. Hope this helps.

Where is map sensor 1986 Isuzu pup 2.3L?

how much is corperator for a 1986 isuzu pup 2.3l

ISUZU engine rpm sensor location?

For an NPR the rpm sensor is located left rear of engine by the frame rail. Its actually the engine speed per service manual but when you need to replace the sensor the parts department calls it the rpm sensor. Good luck.

Where is the crank position sensor located on a 99 Isuzu trooper?

If its a 3.0 td model the crank sensor is situated on the o/s in the engine casing , its accesible from underneath with a long extension and a 10mm socket

How do you replace coolant temp sensor on a Isuzu Rodeo?

how do you replace coolant temp sensor on a rodeo

Is there a sensor that controls the Isuzu vehicross 4 wheel drive system?

Yes, two of them. They are located on the transfer case. As I understand it they send signals to the wheel sensors. I have been trying to find an outlet that sells them other than Isuzu. Isuzu has them priced at over $400 dollars each. Ridiculous!

Where is the oxygen sensor on a 2001 Isuzu Trooper?

on the exhaust manifold.

How do you repair camshaft sensor on Isuzu Rodeo?

please help

Where is the map sensor located on a 2004 Isuzu Axiom?

Egr valve Isuzu part number 8-17096-178-3 (MSRP $197.69) is located on top of the intake manifold on the right side(if you are in the vehicle) rear of the manifold towards the firewall. It is held on by two(2) flanged bolts.