answersLogoWhite

0


Best Answer

I believe under the distributor . It should have a plug attached to it.

User Avatar

Wiki User

โˆ™ 2006-04-22 15:16:41
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the ignition control modular located on a 1996 ford ranger?
Write your answer...
Submit
Related questions

Where is the ignition control modular on an 87 ford ranger?

The ignition module should be attached to the distributor with two small machine screws.


Where is the ignition module located on a Ford Ranger XLT 2.3l?

1994 was the last year the Ranger used an ignition control module on the 2.3 and 2.5. The ignition control module was attached to the lower intake manifold.


Where is the ignition module located on a 1989 ford ranger?

The 1989 Ford Ranger pickup truck ignition module is located on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


95 2.3 ranger is it equipped with an ignition control module?

Yes ( according to motorcraft.com ) Motorcraft ( DY 959 ) Ignition Control Module for 1995 Ford Ranger 2.3 L - SOHC


Where is the ignition module located on a 1995 Ford Ranger 2.3L?

The 1995 Ford Ranger ignition module can be found on the firewall in the engine compartment. The ignition module will be on the drivers side of the firewall.


Where is the location of the ignition control module on a 1993 Ford Ranger 2.3 dual ignition?

It is secured with screws at the fenderwell.


Where is the ignition control module on your 94 ranger 2.3?

On the side of the intake manifold.


What kind of bolts hold the ignition control module in a 1987 Ranger 2.3L?

5.5mm bolts are the kind of bolts that hold the ignition control module in a 1987 Ranger 2.3L. However, 5.0mm bolts may also work.


Where is the ignition starter switch located on a 1991 Ford Ranger?

on top of your steering collum.


What is the Bolt size for ignition control module on a 1988 ford ranger?

4.5 mm but has to be deepwell


Where is the wiper control module located on the 1997 ford ranger?

In a 1997 Ford Ranger, the wiper control module is located behind the radio compartment. It sits on the left side of the compartment.


Can you adjust ignition timing on a 98 Ford Ranger 3.0 liter?

Yes ANSWER No - a 1998 3.0 L Ford Ranger does not have a distributor which would allow you to adjust the ignition timing - it has a coil pack and the ignition timing is controlled by the PCM ( powertrain control module )


Install ignition 2002 Ford Ranger?

install ignition 2002 ford ranger directions


Where is ignition control module on 94 ford ranger 3.0 6 cylinder?

On the lh side mounted to radiator


Where is the EGR valve on a 1987 Ford Ranger located?

On newer vehicals the egr valve is located on ignition emissions system and on the older vehicals it is located on the intake manifold..


Where is the distributor located in the 97 Ford Ranger?

Actually , it doesn't have a distributor , it is EDIS ( Electronic Distributorless Ignition System )


Where is the computer located on a 93 ford ranger?

The computer on a 1993 Ford Ranger is located in the dash in the center just above the transmission hump. The computer is located just below the heater control panel.


Where is the ignition module located on a 1994 ford ranger with a 40 liter?

its mounted under the hood on the driver side fender


Where is a ignition control module on a 1986 Ford Ranger located in the truck?

the ignition module can be in 1 of 2 places for that year and depending on the size of motor. it will either be on the side of the distributor or on the driver side fender. if it's on the distributor, it will be gray and have a plug in it. if it's on the fender, it will be a electrical box and have 2 plugs on it.


Where is the distributor cap located on a Ford Ranger 1994 2.3 L?

A 1994 Ford Ranger has no distributor cap__it uses Distributorless Ignition__the ignition coils are located on the right side of the engine in plain sight (your left when facing the engine )


Why would a 1989 ford ranger lose its power after replacing the ICM ignition control module?

Because you didn't change the rest of the ignition system. Plugs, Wires, Rotor, and Cap are a must for ICM replacement.


Why did your 1990 ford ranger lose power while driving?

i replace the erg,tps,idle control module and ignition control module,and while driving past 30mph i loss power why


Where is the 4x4 control module located on 1994 ford ranger?

somewhere in the cab, probably behind the seats


Where is the abs control module pump located on Ford Ranger?

The Hydraulic Control Unit for the 1995 Ford Ranger 4 wheel anti-lock brake system 4WABS is located in the engine compartment on the left front inner fender panel. It consists of: the brake pressure control valve block, pump motor and hydraulic control unit reservoir. The "brains" of the 4WABS in the Ranger is the Brake Control Module, or Electronic Control Unit (ECU). The ECU/Brake Control Module is mounted in front of the right front corner of the battery on the radiator support.


Where is the ecm on a 1987 Ford Ranger?

the engine control module (ecm) is located behind the passanger kick pannel. which is located by the floor, passanger side.