answersLogoWhite

0


Best Answer

by the the oil filter

User Avatar

Wiki User

โˆ™ 2009-09-04 16:22:08
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Where is the oil sending unit on a 1985 Z24 pickup motor?
Write your answer...
Submit
Related questions

Where is the oil pressure sending unit on a 1986 Toyota Pickup 22R motor?

under the oil filter


Where is the oil sending unit 305 engine Chevrolet engine 1986 pickup?

top rear of the motor, next to the distributor


Where is a oil sending unit at on a 1998 gmc pickup truck motor 5.0 v8?

It is to the right of the Distributor about 2 inches.


Where does the hot wire lead to from the sending unit on a 1986 Chevy s-10 pickup?

Which sending unit? Oil pressure sending unit? Engine temp sending unit? Fuel gauge sending unit?


Where is the oil pressure sending unit located on a 1997 1500 pickup with a 5.7L motor?

At the rear of the engine just behind the distributor


Where is the oil pressure sending unit located on a 1993 Dodge pickup with a 318 motor?

It is on the back of the engine, just to the passenger side of the distributor.


How do you replace oil pressure sending unit on a 77 Chevy pickup 350 motor?

Unplug the electrical connector and slide the OIL SENDING UNIT SOCKET down over it and screw it out. It is a special socket. If you have the room you can screw it out with a pair of pliers.


Where is the oil sending unit on a 1985 ranger 2.8?

Where is the oil sending unit on a 2.8


Where is the location of the oil sending unit on a 1988 Ford F-250 pickup with a 460 engine?

usally by the oil filter or top of motor at the back Rooterman2.


Where is the oil pressure sending unit located on a 1997 1500 pickup with a 318 cubic inch motor?

uhmmmmm there is no such thing a a k1500 with a 318 cubic inch engine.


Where is the oil sending unit on a 1995 gmc pickup?

on the engine


Where is the fuel sending unit on a Chevy S10 Pickup?

In the fuel tank. Fuel tank must be removed to gain access to the sending unit.


Where is the oil PSI sending unit on a 1985 Ford 302 CI motor?

Its located behind the power steering pump, tucked in there nicely out of reach.


Does your 1993 Toyota pickup have a fuel pump or sending unit?

It has both.


Where is the fuel sending unit on a 1994 B 4000 pickup truck?

Any fuel sending unit I've ever seen is mounted into the fuel tank.


Where is the temperature sending unit on a 1988 Toyota pickup?

If it's not located on the thermostat housing, where the top radiator hose attaches to the motor, then it's under the intake air chamber in the head.


Can a bad sending unit on a 1995 dodge 2500 diesel pickup not run?

No


Where is the fuel sending unit on a 1997 sonoma PICKUP?

It's in the gas tank


Were is the location of oil sending unit on 1994 GMC pickup with a V6 4.3?

The oil sending unit is located on the back of the block, directly behind/below the distributor.


Where is the oil pressure sending unit located on a 1990 Toyota pickup with 22R motor?

Directly under the oil filter with a wire hooked to it. Then the wire hooks to the wire harness with another connector.


How do you fix a fuel gauge on a 1985 Ranger pickup?

The ranger has a fuel sending unit inside the gas tank. These are notorious for going out. Only way to change it is to drain and drop the gas tank or remove the bed. The sending units that I have been looking at cost about $100


Installing oil sending unit 1998 gmc pickup?

It is right behind the distributor.


Where is the oil sending unit located on a 1986 Chevrolet Pickup with a 305 Engine?

it is located behind the distributor on top of the block there is the oil sending unit and a oil sending switch with a wire that goes to your choke if it is electric trace it back and you will find it...


Where is the location of oil sending unit on 1993 s10 chev pickup truck?

With a 4.3L engine, the oil pressure sending unit is in the back of the engine just to the drivers side of the distributor.


Why is your 650 prairie radiator fan not working?

A couple of things that you need to first check. Is power present to the fan motor. If not look for the temp sending unit. check for power to the the sending unit. if there is 12v power present there then bypass the sending unit by crossing the terminals. if the motor turns on then replace the sending unit. If there is no power to the send unit, obtain a wiring schematic and trace the power source to the failed component