answersLogoWhite

0


Best Answer
Copy

right above the oil filter there is a wire leading to it. it wont be possible to get to the sending unit without taking the oil filter off.

User Avatar

Wiki User

โˆ™ 2006-03-28 06:18:04
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: Where is the oil signal sending or pressure switch on a 1997 Chrysler Sebring 2.5L V6?
Write your answer...
Submit

Related Questions

Where is the 2004 Chrysler Sebring multi-function switch?

Turn signal headlamp switch


What side of the steering wheel is the signal light pole on a Chrysler Sebring in the United States?

The turn signal switch is on the left.The turn signal switch is on the left.


Why does the right hand turn signal on a 2006 Chrysler Sebring flash faster than the left hand signal when activated?

You have a failed bulb on the right side.


Where is the multi function switch on a 2001 Chrysler Sebring?

The multifunction switch is the turn signal switch and whatever else is part of it.


Why do the turn signals not work in a 2004 Chrysler Sebring?

If the bulbs and fuse are good, replace the turn signal Flasher Relay.


What is wrong if a 1996 Chrysler Sebring computer reads 'cam position sensor no signal'?

There is a problem with the cam sensor or the wiring to it.


What is the meaning of the P1391 code 98 Chrysler sebring convertible?

1391 is for an intermittent loss of the cam sensor or crank sensor signal


What does an oil sending sensor do?

They "sense" the oil pressure inside the engine. If you have an instrument panel oil pressure gauge the sending unit sends an analog signal to the gauge. If you have an oil pressure "idiot light", the sending unit turns the light on when the oil pressure is low.


Where is the speedometer cable located in a 2003 chrysler sebring?

The speedometer signal is all electronic. There is no cable. The signal comes from speed sensors.The speedometer signal is all electronic. There is no cable. The signal comes from speed sensors.


How do you turn on the Fog Lights on a 1997 Chrysler Sebring?

To turn on the fog lights you pull the end of the turn signal lever it will pop out about 1/8th inch.


How do you replace the turn signal flasher on a 1997 Chrysler Sebring?

OPen the trunk or hood, pull out the panel and replace the bulb... If that doesnt work, check your fuses


What does code p2074 mean on a 2004 Chrysler pt cruiser?

Throttle position sensor signal does not agree with manifold pressure sensor signal.


Where is the vss wire on a 2007 chrysler sebring?

There isn't a vehicle speed signal wire on a 2007 Sebring. The transmission computer uses its input and output sensors to factor vehicle speed. It then transmits that message over the communication wires of the vehicle.


What causes signal light to come on solid and not blinking in 98 Chrysler Sebring Convertible?

Check all of you bulbs on the car, more than likely one is burned out...


Where is the flasher unit located on a 1996 Chrysler Sebring convertible?

It is located on the side of the radio between the glove box and the radio if you turn the turn signal on you will feel it flash if you can't here it.


Where is the foglight switch to turn it on 2004 Chrysler sebring?

the multifunction switch... ( turn signal) twist it to turn on the lights and once the lights are on pull it towards the door to turn the fog lights on


Where can you find the signal flasher for a 1998 Chrysler sebring because your signals only turn on and do not blink anymore?

the turn signal relay in on steering wheel top dead center next to the hazard button, remove the steering wheel cover and you can see it


Where is the fog light switch on a 1996 Chrysler sebring convertible?

On the turn signal indicator arm. Switch on the headlights, make sure the high beam is off, then pull out the rotating light switch.


Where is the switch for fog lamps located on a 1997 Chrysler Sebring?

Pull the end of the turn signal lever out about 1/8th inch. This only works with the lights on. Fog lamps will not work with headlights off.


What is the function of a oil pressure switch?

If it is an oil pressure switch it grounds out internally at a set pressure to send a?æsignal to the oil pressure light that the oil pressure is low. An oil pressure sending unit sends a ?ævariable voltage signal to the gauge indicating the pressure.


On a 1996 Chrysler sebring 2.5 V6 what is at the receiving end of the crank position sensor does it get its signal from the crank shaft itself or is something attached to the crank?

There is a tone wheel on the crank/flywheel that the sensor reads off of, if that is your question.


Where is turn signal bulb located in a 1995 Chrysler 300?

Chrysler did not make a 300 in 1995. Turn signal bulbs are on each corner of the vehicle.


Where is the turn signal control relay located on a 1998 Chrysler Sebring Coupe?

I have a turn signal light that keeps flashing regardless of the control arm position. I think that the problem is in the turn signal control relay but I don't know where it is located. I did find the 3 prong relay located behind the center console but this is not the problem because I replaced it and have the same problem.


Where is the turn signal relay located on a 1997 Chrysler Sebring?

there is a compartment on the driver side when you open the driver door look by the hinge you will see a panel pull of relay is in there BEHIND A/C AND HEATER CONTROL PANEL, IN CENTER CONSOLE.


Where is the output VSS on a 2000 Chrysler Sebring?

The vehicle speed signal comes from the transmission output speed sensor on the front driver side of the transmission case.The vehicle speed signal comes from the transmission output speed sensor on the front driver side of the transmission case.