on my 93's V6 it's right after the exhaust pipes from the engine join into one pipe.
The 91-92 have a different engine than the 93 and newer, But it is on the driver side just behind the front tire as the pipes join together, you will have to remove the skid plate to get to it, the sensor is on top of the pipe. Make sure its cold before you try removing it, you can't help but touch the exhaust. Make sure you get an O2 socket, and I use Parts Blaster, most parts stores carry it. It will be rather rusty and hard to turn. When you put the new one on you can use some anti seize on the threads to prevent the new one from rusting up as much. The 91-92 actually use a GM engine, where as the 93 and up use the Isuzu engine.
6.0 for the 3.2 liter
Hi, How Do You Replace a Starter on a 1995 Isuzu Rodeo, V6, 3.2 liter engine? Does anyone know where the starter is? Help. How Do You Replace a Starter on a 1995 Isuzu Rodeo, automatic, 4wd, V6, 3.2 liter engine? Does anyone know where the starter is? Thanks alot.
The 2.2 liter four cylinder engine and the 3.2 liter V6 engine in a 2003 Isuzu Rodeo both have a timing BELT
The 1990 Isuzu 2.8 liter engine MAF sensor can be found on the firewall in the engine compartment. The sensor will be on the passenger side of the firewall.
The temperature sensor on a 1994 Rodeo 3.2 liter is located on the back of the engine. You need to remove the manifold to access the sensor.
Yes , according to the Gates website ( they make timing belts etc. ) the 3.2 liter V6 in a 2000 Isuzu Rodeo is an interference engine
Both the 2.2 liter 4 cylinder and the 3.2 liter V6 engines in a 1999 Isuzu Rodeo have a TIMING BELT and both are interference engines ( according to Gates , they make timing belts etc. )
Yes , the 2.2 liter 4 cylinder and the 3.2 liter V6 engines each have timing belts
Your 3.2 liter V6 engine has a timing BELT
98 was the year when the Rodeo crossed over from the first generation platform to the second generation platform, and both are within the 1998 model year. There were several engine options available for the Isuzu MU, but the Rodeo name was only used in the North American market. So you have either a 3.2 liter or 3.5 liter V6 engine.
i have a izuso rodeo 1999 3.5 liter i need how i fix the code po452 were is the location is the sensor and how is the sensor
Can you show me a diagram of the upstream oxygen sensor on a 3.5l liter Oldsmobile Intrigue engine?
The oxygen sensor on a 1999 Oldsmobile Intrigue 3.3 liter is in the exhaust manifold/pipes
It just has ( 1 ) oxygen sensor , before the catalytic converter ( upstream )
You can find the crank sensor on the back of your 1993 3.4 liter engine. You will need to remove the rear engine cover in order to access the crankshaft sensor.
the o2 sensor is located on the exaust manifold
The O2 sensor after the catalytic converter.
The 2004 Dodge Intrepid oxygen sensor can be found on the back of the air cleaner housing. Remove the wiring harness. Remove the oxygen sensor retaining screws. Reverse the process to install the new oxygen sensor.
It is the sensor in the outlet of the catalytic converter.
Yes, and no... GM and Isuzu are partners to some degree. I personly have a '97 Rodeo, and am looking to install a bigger better engine, and have come across several interresting facts. The Isuzu 3.2 liter uses the GM 60 degree V6 bolt pattern to the transmission, as well as obviously the GM V6's do. Currently searching for an '04 3.8 liter pushrod V6 that will use my ignition system (coil on plug) and the MPFI.
It is threaded into the exhaust manifold.
The oxygen sensor on the 1988 ford 2.9 liter engine is located on the exhaust pipe just behind the right exhaust manifold. It screws into the exhaust pipe and has a small wire running to the tip of it. Just unplug the wire and turn out the sensor with a wrench.
There is one on each side of the catalytic converter.
Bank 2 is the passenger side exhaust pipe and sensor 2 will be the closest sensor to the converter.