Best Answer

The OBD II connector is under the ashtray. Remove the ashtray and slide the plastic cover to the left and the connector will be visible.

User Avatar

Wiki User

โˆ™ 2007-09-16 13:41:33
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the plug for a scan tool located on a 1996 jetta gl?
Write your answer...
Related questions

Where is the computer located on a 2001 VW Jetta and how can you access it?

under the steering wheel to the left you need to open that panel and you can plug into to scan your car. hope that's what your looking for.

Where is the scan tool plug-in located in a 2000 Hyundai Tiburon?

Under the steering wheel on dash.

Where is the scan tool plug in located in a 1995 v8 4.6 l thunderbird LX?

On passenger side under dash

How do you hook up a scan tool for a 1999 Malibu?

The DTC (Diagnostic Trouble Code) connector would be located under the drivers side of the dash. Plug the scanner into the DTC connector and then follow directions that came with your scan tool.

How do you reset the check engine light on a 1999 volkswagen jetta?

The check engine light has to be reset with a OBD scan tool

Where is the scan tool plug-in located in a 1995 Ford Thunderbird?

My 95 Ford Thunderbird service manual shows the scan tool plug-in (Data Link Connector) on the R.H. side of the instrument panel, under the glove compartment door and on the R.H. side of the engine compartment over the wheel well. This is for the 3.8L V6 engine.

How do you get the engine codes on a 2002 mercury villager?

Plug in a scan tool.

How do you scan a drawing onto the computer?

Buy a scanner, put the drawing onto it, plug it in to the computer, and follow the scanner's instructions to scan it.

How do you scan yourself to go to digital world?

well first, you dont scan in. you have to insert a 2 foot plug. good luck.

How do you chek transmission iol from a jetta 20000?

You cant check it,It is a sealed system, it needs to go to a shop and get checked with a scan tool

How can you program a keyfob on a Chrysler lhs 1996 if you only have one fob?

The dealer scan tool is required.The dealer scan tool is required.

How do you erase trouble codes on 1996 Pontiac Bonneville?

with a scan tool

Where do i plug in the obd2 scan tool?

Into the diagnostic connector under the dash on the driver side.

How do you scan a picture onto your computer?

Buy yourself a scanner Install the driver (won't be necessary for a plug and play). Search for windows fax and scan in the start menu. SCAN!!!!

Where do you charge the iPod?

Plug it into a USB socket. If you want to charge it in the car, Scan Computers sell adapters so you can plug a USB stick into a car.

How do you reset the computer on a 1996 Dodge Caravan?

Scan tool or battery disconnect.

Where is the scan tool plug on a 1988 Lincoln Town Car?

Under the hood on the passenger side.

How do you adjust the idle on a jetta tdi?

you would need to have a scan tool, ross-tech or a vw dealer tool, in there you can set the idle for the car... with out it, your sol sadly

How to reset check the engine light on 1996 Chevy Camaro Z28 wo a scan tool?

AnswerWith an OBD2 scan tool.Possibly by unhooking the battery.

How do you reset the computer on a 1996 Ford Taurus?

OBD2 scan tool. i dont know

What is obd port?

Obd-on board diagnostic. The port is the plug the scan tool or code reader connects to.

What scan tool do you need to have to check a 1993 jeep?

An OBD 1 scanner with the Chrylser plug adapter.

How to restart a grand am se 1999 or unlock the stereo?

If you take the car to a dealer they can plug it in to a scan tool and get the codes by calling into GM and inputting them into the stereo for you[was no cost when I asked]. The code is made up from the vehicles VIN. I am assuming they plug in the scan tool to verify the radio is from the car it is in and not stolen.

How do you program a keyless entry for a 1996 Chrysler Sebring convertible?

The dealers scan tool is required.

How do you reset the computer on a 1996 Dodge Ram?

With a scan tool, or by disconnecting the battery for 10 minutes.