answersLogoWhite

0


Best Answer

on the outboard side near the lugs.

User Avatar

Wiki User

โˆ™ 2005-09-30 10:59:14
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the screw holding on the rear brake drum of a 1991 Isuzu pickup?
Write your answer...
Submit
Related questions

How do you replace the brake light on a 1991 Nissan pickup?

Remove the light assy and screw it in from the rear.


How do you change the front speakers on a 1995 Isuzu Rodeo?

The speaker covers are held in with a screw, remove it and tilt it out away from where the screw was. then remove the screws holding the speaker in and remove the speaker.


How do you unfreez the emergency brakes on a 1993 Nissan pickup truck?

on the back side of hub,theres a rubber plug,remove,theres a star screw that separates your brake shoes,put screw driver on star screw and push down to separate brake shoes.it will help you take hub off,your brake cable might need replaced.


You are trying to change a rear brake bulb on a 1999 Isuzu Rodeo you have already removed the 2 screws but something it still not allowing you to remove the cover?

There is a third screw between the brake light and the bumper.


How do you remove the brake drum on a 1995 Isuzu pickup?

Do the following to remove the brake drum on 1995 Isuzu Pickup. - Remove wheel from the brake drum- Remove the Philips screw that holds the brake drum to the axle plate. The brake drum is now free to be removed but is usually stuck to the lug bolts.- spray penetrating oil on the lug nuts (be sure to put card board below wheel to catch the oil that will run off.- Use a plastic hammer and hammer the drum off the axle plate. - An alternate way is to place a 2 x 4 across the top of the lug nuts and use two c-clamps to pry the drum off the lug nuts.


How do you remove the distributor rotor on a 1989 Isuzu amigo?

There are 3 screws holding the distributor cap on. After removing the cap, there is a small Phillips head set screw holding the rotor in place on the shaft portion of the rotor.


1985 Nissan pickup parking brake adjustment?

look under driver side by ddoor,unscrew lock nut and tighten other screw until brake is good,then tighten lock nut.


How do you replace brake light on a 1995 Isuzu Rodeo?

If its the bulb you have to unscrew the light cover and pull out the old bulb and put the new one in.Then screw the cover back on.


How does a brake bleed screw work on a 1998 Nissan Pathfinder?

The bleed screw on the calipers of brake systems are for 'bleeding' air out of the brake lines.


How do you get window crank off 1997 Nissan pickup xe?

you can push the doorand get a flat head screw driver and push the clip that's holding it on, do it with door open.


How do you adjust the emergency brake on my 1995 Nissan 240sx?

The 1995 Nissan 240 emergency brake has an adjustment screw on the brake pad. Turn the adjustment screw to adjust the brake height.


How do you reset the oxygen sensor on your 1993 Isuzu pickup?

I have been told it time to remove the dash and move a screw from one hole to another. This can be found on other sites. We are going to try it this weekend and see if it works.


How do you wind back the brake pistons on your Renault Scenic not electric braking?

You can adjust the brake pistons by adjusting the brake piston adjustment screw. Turn the screw to the right in order to back off the brake piston.


How do you set the injector pump timing on a 4HF1 Isuzu engine?

You can set the injector pump timing on a 4HF1 Isuzu engine by adjusting the fuel injection screw. The adjusting screw will restrict the amount of fuel to be injected.


How do you get the foot brake on Honda Recon unstuck?

Crack the bleeder screw pry calipers apart with screw driver rebuild the brake ....tip to get brake piston out use compressed air


Pushing rear brake calipor back piston on 2000 Chevy 1500 pickup?

If rear brake caliper is used for emergency brakes also - piston is threaded and requires a special tool (not expensive available at Sears or auto parts) to screw into caliper housing


How do you replace slave cylinder for a 1991 Nissan pickup?

at the transmission,theres arubber boot with afork coming thru it.and the slave cylinders end is touchig the fork remove 2 bolts holding it on,replace and fill clutch masterwith dot 3 brake fluidand havesomeone pump the clutch afew times ,then open bleeder screw also follow line from cluch master cylider ,there should be another bleeder screw.


How do you change brake light in a 2006F-150 pickup?

Put down the tail gate, use a Phillips head screw driver and take off the light cover then unplug the connection and unscrew the light.


Can you unscrew the bleeder screw and pumped the brakes to empty out the brake fluid?

Yes, that is what the bleeder screw is for


How to adjust the brake on a John Deere LA100?

on the left side behind the tire as you are looking at the tractor from the rear is the brake rotor and a screw inside of a spring beside it ... simply tighten that screw until satisfied with brake operation.


How do you replace the brake light switch on a 1997 Yukon?

Go to the brake pedal and it is mounted under there then unplug the connector and screw out the part then screw the new one in and replug the connector in.


What is the function of a screw?

Retaining or holding things together.


How do you pull rear brake hub on 2004 outlander Mitsubishi?

there are two holes on the rear brake hub. Find the correct size bolt and screw them in the holes. Screw one then the other till it pops...then slide it off. there are two holes on the rear brake hub. Find the correct size bolt and screw them in the holes. Screw one then the other till it pops...then slide it off.


How do you change a rear brake light on a SEAt Ibiza?

Changing a rear brake light on a SEAt Ibiza is simple and will not take a lot of time to do. All you do is unscrew the brake light cover, unscrew the old brake light and then screw back in the new light then screw back on the cover.


How does vacuum pump force brake fluid through the lines?

Screw taking special vacuum brake system is in the winding cursed the brake.

Study guides

๐Ÿ““
Create a Study Guide