answersLogoWhite

0

  • Car Starting Problems
  • Starters and Ignition Systems
  • Chevy Suburban
  • Chevy Cheyenne

Where is the starter at on a 1998 Chevy Cheyenne 350?

User Avatar

Wiki User

βˆ™ 2006-07-20 18:37:59

Best Answer
Copy

Bottom of the engine, passenger side, connected between the engine and transmission bell housing.

2006-07-20 18:37:59
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

Is the starter on a 1970 Chevy 350 different from a 1978 Chevy 350?

no


Does a 350 Chevy engine fit into a 1989 Chevy Cheyenne?

Yep


Will a Chevy 350 starter fit on a Chevy 454?

no it wont to small of a starter


Where is the solenoid on Chevy 350?

It's bolted to the top of the starter.


350 Chevy starter?

Need more info: Thank you.


Where is the selanoid on a Chevy 350?

There is one mounted on top of the starter.


Where is the anti knock sensor on a Chevy 350 block?

It is in front of the starter on my van.1990 350


Will a 350 starter work on 400 small block Chevy?

Yes.


Can you use a 6.2 ltr diesel 700r4 tranny on your 72 Chevy Cheyenne that has a 350?

yes you can


How do you get a 72 Chevy Cheyenne with 350 engine started?

air, fuel, and spark is all you need.


Will Chevy 350 and a 454 starter interchange?

Yes, but the big block may need a hi-torque starter.


What are the engine sizes for a 1973 Chevy Cheyenne?

The engine sizes for the 1972 Chevy Cheyenne included the 250, the 262, the 292, the 305, the 350, and the 400. The 454 was also offered for the 1973 model year.


What is the starter bolt torque on a 350 Chevy?

45-50 ft./lbs.


Where do wires go on 350 chevy mini starter?

The starter needs a large wire from the battery and a wire from the starter switch. These are connected to the solenoid that is attached to the starter.


Will a 350 motor out of a 1993 Chevy 1500 pick up fit into a 1994 Chevy Cheyenne that had a 5.0?

YES, they are basically the same engines.


Can a 1998 Chevy 350 head fit a 1984 350 block?

yes it will fit but you will have to change the intake manifold to the 1998 style.


When do you shim a Chevy 350 starter?

Very rarely have to shim a starter. If there is excessive noise or a disengagement problem it will need to be shimmed.


How do you change a starter on a Chevy 350?

Disconnect the - battery cable Raise and support vehicle Remove wires at top of starter Remove starter mounting bolts Remove starter


Why does the starter for a 350 Chevy grind and sti?

Wrong starter, wrong fly-wheel, Bad starter drive, worn fly-wheel. Starter may need to be shimed.


Starter Wiring diagram Chevy 350?

starter on 67 camaro which wire goes were. There are two one purple one yellow.


Where is the starter on a 1989 Chevrolet cheyenne truck 350 motor automatic 1500 series?

The starter should be located at the rear of the engine next to the flywheel on the passenger side. ~ D


Will a starter off a 1987 Yamaha 350 moto fit on a 1998 Yamaha 350 warrior?

if the 87 is a warrior yes


What models of Chevy use the 350 engine?

The chevy 350 engines were produced in production models of Chevy between 1968 until 1998. It was used in several Chevy models such as Chevrolet Camaro and Chevrolet corvettes.


Why does the starter for a Chevy 350 grind but will not engage the flywheel?

It could be the starter drive, the solenoid, or the ring gear itself. Best to pull the starter out of there and see what's going on.


Will a 350 engine fit into a 1998 Chevy Tracker?

i have heard it will but i am not totally sure because i dont have a 350 to try it with